background image

7

Filter Removal and Service

Kooltronic Heat Exchanger feature an easily removable inlet filter to
facilitate necessary cleaning.

1)

Move the filter forward, using attached tab, to clear the
near filter retainer.  Pull the filter downward and toward you until the 
far side of the filter clears the far filter retainer.

2)

After removal, the filter should be flushed under warm running water 
with the clean side up, driving contaminants out the dirty side of the 
filter.  If the accumulated dirt is oily, washing in a detergent bath is 
recommended, followed by warm water rinse as above.

3)

The filter may be sprayed with 

Kooltronic A-16 Filter Recoating 

Adhesive

to trap fine airborne contaminants, or they can simply 

be dried and reinstalled as strainer type filters. 

Recoating

is recommended for the best results.

4)

Reinstall the filter:  (a) Holding the tab, slide the filter into the near 
retainer, (b) press filter against the unit and (c) slide forward into
far retainer.

CAUTION

Do not operate the Heat Exchanger for extended periods

of time with the filter removed.  The heat exchanger element

may become clogged with dust or lint from the ambient

environment.  A clogged heat exchanger element is not 

readily detected and will give the same reaction as clogged

filter.  A clean filter is the best protection.

VIII. Packing Procedure

Keep Heat Exchanger in proper upright position.

Pack Heat Exchanger in an appropriate carton (preferably original carton if possible),
with adequate internal protective packaging, making sure carton is marked properly.

For local controlled transportation, strap carton where possible, to a secure part of
truck to prevent falling or sliding, minimizing vibration, etc.

For common carrier shipment, band unit(s) securely to a pallet.  Unpalletized ship-
ment risks severe damage which voids the warranty.

Содержание KTHE300









Отзывы: