background image

6

Major Component Replacements*

Model

KTHE300

KTHE500

Blower Assembly

5417-00-35

6015-00-129

Blower Capacitor

0452-03

0452-06

Blower Motor

0261-08

0261-08

Coil

0744-06

0744-07

Filter

7001F

10501F

* Part numbers shown are for 115V, 60 Hz. For 230V, 60Hz and all 50Hz, consult Kooltronic.

VII. Maintenance

Kooltronic Air-Cooled Heat Exchangers are designed to require only routine cleaning
of air filters and the heat exchanger element to assure unimpeded airflow through the
heat exchanger element. It is not possible to recommend specific filter cleaning inter-
vals since the level and the nature of air borne particulate matter differs widely with
each installation. It is generally sufficient to remove and wash the reusable alu-
minum mesh air filter when the outer surface of these filters appear covered with a thin
layer of dust or lint. Filter recoating adhesive is recommended. Appropriate dis-
posable filters are available from Kooltronic.

If filter service is neglected or delayed, the heat exchanger will not perform at its design
capacity. The first indication of excessively clogged air filter is usually a gradual
increase of temperature within the equipment cabinet. Continued operation under
these conditions will cause damage, shorten blower motor life and void the warranty.

CAUTION

Disconnect electric power from the Heat Exchanger

before proceeding.

Содержание KTHE300









Отзывы: