manualshive.com logo in svg

Kontron KTG41/ATXu, Руководство пользователя

Поделиться
Скачать
Kontron KTG41/ATXu Скачать руководство пользователя страница 7

KTD-00781-A  

KTG41 family 

Page 7 of 78 

 

 

www.kontron.com

Introduction

 

This manual describes the KTG41/ATXu board made by KONTRON Technology A/S. The board will also be 
denoted KTG41. 
 
The KTQ41 boards supports the Intel® Core™2 Quad processor Q9000 series, the Intel® Core™2 Duo 
processor E7000 and E8000 series with a maximum TDP of 95W. These processors belong to the Intel 

Yorkfield and

 

Wolfdale 

families. 

 
Use of this Users Guide implies a basic knowledge of PC-AT hard- and software. This manual is focused on 
describing the KTG41 special features and is not intended to be a standard PC-AT textbook.  
 
New users are recommended to study the short installation procedure stated in the following chapter before 
switching-on the power. 
 
All configuration and setup of the CPU board is either done automatically or by the user in the CMOS setup 
menus, except for the CMOS Clear jumper (JBAT1), SPI jumper (JP6), Interface BIOS jumper (JP4 and 
JP5).  
 
 
 

Содержание KTG41/ATXu















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды