manualshive.com logo in svg

Kontron KTG41/ATXu, Руководство пользователя

Поделиться
Скачать
Kontron KTG41/ATXu Скачать руководство пользователя страница 31

KTD-00781-A  

KTG41 family 

Page 31 of 78 

 

 

www.kontron.com

3.7 

Serial ATA Hard Disk interface 

The KTG41 has integrated SATA Host controller that supports independent DMA operation on four SATA 
(Serial ATA) ports for connection of one device per SATA connector. The SATA ports supports data transfer 
rates of up to 3.0Gbit/s (300MB/s) and the SATA controller supports AHCI mode and has integrated RAID 
functionality with support for RAID modes 0, 1, 5 and 10 (Linux O/S only support for RAID 0 and 1).   
 
For compatibility, the underlying Serial ATA functionality is transparent to the operating system. The Serial 
ATA controller can operate in both legacy and native modes. In legacy mode, standard IDE I/O and IRQ 
resources are assigned (IRQ 14 and 15). In Native mode, standard PCI Conventional bus resource steering 
is used. Native mode is the preferred mode for configurations using the Windows XP and Windows Vista 
operating systems. 
 
The KTG41 supports the following RAID (Redundant Array of Independent Drives) levels: 

•

  RAID 0 - data striping 

•

  RAID 1 - data mirroring 

•

  RAID 0+1 (or RAID 10) - data striping and mirroring 

•

  RAID 5 - distributed parity 

•

 Matrix 

2+2 

Limitations depending on Target Operating System apply. 

3.7.1  SATA Hard Disk Connector (SATA1, SATA2, SATA3, SATA4) 

 

SATA: 

 

PIN 

Signal 

Type 

Ioh/Iol 

Pull 

U/D 

Note 

 

 

 

 

 

 

 

 

 

1 

 

GND 

PWR 

- 

- 

 

 

2 

 

SATA* TX+ 

 

 

 

 

 

3 

 

SATA* TX- 

 

 

 

 

 

4 

 

GND 

PWR 

- 

- 

 

 

5 

 

SATA* RX- 

 

 

 

 

 

6 

 

SATA* RX+ 

 

 

 

 

 

7 

 

GND 

PWR 

- 

- 

 

  
The signals used for the primary Serial ATA hard disk interface are the following: 
 

Signal 

Description 

SATA* RX+ 

SATA* RX- 

Host transmitter differential signal pair 

SATA* TX+ 

SATA* TX- 

Host receiver differential signal pair 

 
“*” specifies 1, 2, 3, 4 depending on SATA port.  
 

Содержание KTG41/ATXu















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды