manualshive.com logo in svg

Kontron KTG41/ATXu, Руководство пользователя

Поделиться
Скачать
Kontron KTG41/ATXu Скачать руководство пользователя страница 58

KTD-00781-A  

KTG41 family 

Page 58 of 78 

 

 

www.kontron.com

6.6.2  Advanced settings – IDE Configuration 

 

BIOS SETUP UTILITY 

 

      

 

Advanced

   

    

   

       

 

 

         

 

    

     

IDE Configuration 

 

ATA/IDE Configuration  

    

         [Enhanced]

 

   Configure SATA as                [SATA] 

   Configure SATA Channels          [Before PATA] 
    

►

 Primary IDE Master                : [Hard Disk] 

►

 Primary IDE Slave                 : [Not Detected] 

►

 Secondary IDE Master              : [Not Detected] 

►

 Secondary IDE Slave               : [Not Detected] 

►

 Third IDE Master                  : [Not Detected] 

►

 Third IDE Slave                   : [Not Detected] 

 
 

Hard Disk Write Protect        [Disabled] 
IDE Detect Time Out (Sec)      [35] 

ATA(PI) 80Pin Cable Detection  [Host & Device] 

 
Sata BIOS Extension            [Enabled] 
 
 

        Options 

Disabled 

Compatible

 

Enhanced 
 

 
 

 

 
 
 

 

 
 

<-    Select Screen 

||    Select Item 
+-    change option 

F1    General Help 

F10   Save and Exit 
ESC   Exit 
 

v02.61 (C)Copyright 1985-2006, American Megatrends, Inc.

 

 
 

Feature

 

Options

 

Description

 

ATA/IDE Configuration                Disabled 

Compatible 

Enhanced 

Disabled 
Compatible 
Enhanced 

Configure SATA as 

IDE 

RAID 
AHCI 

IDE 
RAID 
AHCI 

Configure SATA Channels 

Before Pata 

Behind Pata 

Before Pata 
Behind Pata 

 
 

Feature

 

Options

 

Description

 

Hard Disk Write Protect         

Disabled 

Enabled 

Disable/Enable device write protection. This will be 
effective only if device is accessed through BIOS 

IDE Detect Time Out (Sec)        0 

5 
10 
15 
20 
25 
30 

35 

Select the timeout value for detecting ATA/ATAPI 
device(s) 

Sata BIOS Extension  

Disabled 

Enabled 

Disabled 
Enabled 

 

Содержание KTG41/ATXu















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды