KONRAD KT-RFCT 2400A Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 29

background image

KT-RFCT 2400A

User Manual – KT-RFCT 2400A

Version: 2.0

22/29



Click on the folder icon next to the Image/Package Path text box and navigate to the

location of the firmware image file which will be a dated zip file e.g. 2018_07_31.zip



Click the Upload button. A licence information screen will pop up, click Agree.



Click the Update Firmware button – A pop up warning dialog will be displayed which

will explain what will happen during the firmware update process, click OK to

proceed.



Wait until the firmware update is complete which is indicated when the Updater

status shows ‘Finished!’. The firmware update will take at least 5 minutes, do NOT

disconnect DC power or attempt to use the KT-RFCT 2400 during the firmware

update process.

Stage 1

«
...
20
21
22
23
24
...
»

Содержание KT-RFCT 2400A






























Отзывы:

Нет отзывов

Похожие инструкции для KT-RFCT 2400A

Бренд: Waterwise Страницы: 12

Бренд: ParaBody Страницы: 38

Бренд: Quivogne Страницы: 13

NI VISION PCI-8254R

Бренд: National Instruments Страницы: 13

NI VISION PCI-8254R

Бренд: National Instruments Страницы: 16

Бренд: National Instruments Страницы: 10

Бренд: National Instruments Страницы: 39

Бренд: National Instruments Страницы: 65

Бренд: haacon Страницы: 59

Бренд: Ofa Bamberg Страницы: 80

Sonorex Super RK 31

Бренд: BANDELIN Страницы: 21

BTL7-A/E501-M Series

Бренд: Balluff Страницы: 194

Бренд: B.Pro Страницы: 48

Бренд: ABB Страницы: 16

Бренд: ABB Страницы: 2

Бренд: Sabo Страницы: 76

Бренд: GAPOSA Страницы: 32

Бренд: Hedson Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды