background image

4

Setting Up

•Be sure to use indoor wiring for within the specified voltage range.   For extension cord, use

indoor wiring of the specified rating or more.
·Failure to do so could result in fire or equipment failure.

•Never plug more than one cord at a time in the electrical receptacle.

·Doing so could result in fire or electrical shock.

•Do not lay the power cord where people walk through.   You may tread on or stumble

over them.
·You may fall down and get injured or the cord may get damaged.

•Do not put anything heavy on the pipe connecting the projector unit and the cockpit

unit, nor pull the pipe forcibly.   Never install the machine with the pipe being
disconnected and the bundled wires being exposed. (GN672-UC only)
·Doing so could redult in eguipment failure, electrical shock or fire.

•Be sure to connect the attached grounding wire. (See page 28.)

·Failure to do so may result in electric shock or trouble.

•Clearances of 100 mm (3.94in) or more should be created between the game

machine and walls.

プ グ

CAUTION

Operation

4

WARNING

Precautions for use

•If there is any abnormality such as smoke, bad smell or abnormal noise being

emitted from the machine, immediately turn OFF the power switch and unplug the
power cord from the receptacle to stop operating it.

·Using the machine in abnormal conditions could result in fire or accidents.

In case of abnormality

1 Turn OFF the power switch.

2 Unplug the power cord from the receptacle.

3 Contact your nearest dealer.

•Do not leave the power cord plugged improperly or covered with dust.

·Doing so could result in electrical shock or fire, so inspect the power cord periodically.

•Never disassemble, repair or modify any section other than those specified in this

manual.

·Doing so could result in fire, malfunction or equipment failure.
·Ask your nearest dealer to perform repairing, etc..

 ·We do not assume any responsibility for any damages that would be caused

 by tampering with the machine.

Содержание Solar Assault
















































Отзывы: