background image

A

T

T

E

N

T

I

O

N

A

T

T

E

N

T

I

O

N

Any work of maintenance, adjustment and cleaning must be done with the machine on the 
ground (stable conditions), turning off the ATV or lawn tractor engine and removing the key.

Read carefully the safety labels applied on the machine and follow the instructions.

A

T

T

E

N

T

I

O

N

  -

  W

A

R

N

I

N

G

A

T

T

E

N

T

I

O

N

  -

  W

A

R

N

I

N

G

The  operator  during  the  period  of  use,  maintenance,  repair,  handling  or  storing  of  the 
machine  must  wear  accident-prevention  shoes  and  safety  gloves.  Moreover,  if  it  is 
necessary he must wear suitable protections such as earplugs, dust masks and protective 
glasses.

During loading, there is the danger of powders inhalation produced by fertilizer mixing. It is 
suggested to use suitable safety systems of breathing, like powder masks or masks with 
filter.

The machine is designed for being used by a single operator who, during the use, must 
always stay in the stationing control on the vehicle.

 Never work with this machine if you are tired, sick or after drinking, drugs or medicines.

D

A

N

G

E

R

D

A

N

G

E

R

It is forbidden to climb or to transport somebody on spreader.

Do not put hands inside the hopper for any reason while machine is in motion or capable of 
moving under its own power.

Keep hopper free from foreign bodies (bags, tools, miscellaneous), as they could damage 
the operations or the operator. 

Generally fertilizers are corrosive. For this reason, it is important that any particles of fertilizer 
NOT stay in the machine for a long period of time. 

Clean the hopper and the distributor after each use of the machine.

If during cleaning operations air or water with pressure are used, it is necessary to wear 
glasses and safety masks and keep away persons or animals from the machine.

Before connecting the machine to the vehicle check that this is in good conditions and that 
brakes work correctly, especially if you work on sloping grounds. . 

Disconnect the spreader from vehicle only on level ground (with empty hopper), checking 
that the machine is stable.

W

A

R

N

I

N

G

W

A

R

N

I

N

G

During transport operations, stocking and deployment of the fertilizers. The operator must 
follow all the label instructions and particularly to the content of the written risks and the 
precaution suggestions.

6

Содержание ATVSS350













Отзывы: