GE ATS1190, Руководство пользователя

Страница: 1 / 16

© 2003 GE Interlogix B.V. MAINST-ATS1190
ATS1190/1192
Smart Card-Leser
D
™
ATS1190/1192 ATS1105 ATS1170 ATS2000/3000
/4000
ATS1250/1260 ATS1250/1260
Localbus
Kabel J2 J1 J1 Tür 1, 2, 3, 4 Komm.
Rot 12 V 12 V 12 V 12 V 12 V
Schwarz 0 V 0 V 0 V 0 V 0 V
Grün D0 D0 D0 D0 D0
Weiß D1 D1 D1 D1 D1
Gelb - L2 - L2 -
Braun - L1 - L1
Austrittstaster
( => 0 V)
Blau - L3 - BZ -
Violett - - -
Mit 4K7 (in Serie)
zu Alarmeingang 3
Mit 4K7 (in Serie)
zu Alarmeingang 3
Y
ATS 1190 ATS1192
Smart Card Reader
I
NTRODUCTION
The ATS1190/1192 Smart Card Reader is a multifunction,
all-purpose proximity card reader suitable for all locations requiring
a short-range reader. The reader can be connected directly to
the ATS Control Panel (see figure
Y
). It is configurable through
a Menu system accessible via the BUS or by Configuration
cards programmed through Titan and the Aritech Smart Card
Programmer (ATS1621/22).
The reader operates from 9 to 14 VDC. It has a quiescent
current consumption of less than 25 mA and less than 80 mA
when reading a card. The ATS1190 is supplied standard with
a white removable dress cover, which can be interchanged with
one of four other colours available.
The ATS1192 is a heavy-duty version designed for standard
door frames.
Both the ATS1190 & ATS1192 are waterproof.
Figure
™
: Smart Card Reader
Blue LED: Door open Red LED: Door open
Disarmed Armed
M
OUNTING
The reader can be mounted on any flat surface by two pan
head screws, 3.0-3.5 mm diameter, located under the dress
cover. A slightly reduced range will be experienced when mounted
on metal surfaces. If mounting in an outdoor environment, ensure
that the blue LED is at the top.
It is not recommended to use countersunk screws.
For the ATS1190 the dress cover can be removed to expose
the mounting screw by gently prizing the sides away from the
main body to release the retaining clips and gently pulling on
the connection cord. Do not use excessive force or the reader
can be irreparably damaged.
After mounting, gently press the cover over the main body
until it locks into place.
RAS
ADDRESSING
The address of the reader for BUS operations is set to the
default address RAS 16. Using a configuration card or accessing
its on-line Menu system when connected to the RS485 BUS can
change this. See the Programming Guide, Reader Address, for
further details.
T
AMPER
The reader is provided with a Tamper facility. When connected
to the BUS, Tamper data is transmitted to the Advisor Master
with system data. An external Open Collector output (violet wire)
can be configured as a Tamper control for both online and
offline operation.
R
EADER WIRING
Red: Positive 9 to 14 VDC supply
Black: 0 Volts DC supply ground
Green: D0 /
Clock
RS485 Data - Wiegand Data 0
Absolute maximum, 12 V @ 10 mA
White: D1 /
Data
RS485 Data + Wiegand Data 1
Absolute maximum, 12 V @ 10 mA
Brown: LED 1 Offline LED control configured to “Two Wire
Control” will control the red LED only
Wire grounded: Red LED on
Wire open: Red LED off
Wire at +5 V to +12 V: Red LED off or,
offline LED control configured to “One
Wire Control” will control both the red
and blue LED’s
Wire grounded: Blue LED on
Wire open circuit: Both LED’s off
Wire at + 5 V to 12 V: Red LED on
Absolute maximum, 14 V
All rights reserved 08/2003