Komatsu PC210-8 Скачать руководство пользователя

Страница: 841 / 1200

40 Troubleshooting

UEN00244-02

PC210, 230, 240-8

E-10 Hydraulic oil temperature gauge does not indicate normally

Circuit diagram related to hydraulic oil temperature sensor

Trouble

(1) While hydraulic oil temperature is rising normally, temperature gauge does not rise from white range

(C).

(2) While hydraulic oil temperature is stabilized normally, temperature gauge rises to red range (H).

Related infor-

mation

• Signals of hydraulic oil temperature sensor are input to pump controller and then transmitted to

machine monitor through communication system.

• Hydraulic oil temperature can be checked with monitoring function.

(Code: 04401 Hydraulic oil temperature)

Possible causes

and standard

value in normal

state

Cause

Standard value in normal state/Remarks on troubleshooting

Defective hydraulic oil tem-
perature sensor (Internal dis-
connection or short circuit)

Prepare with starting switch OFF, then carry out troubleshooting
without turning starting switch ON.

P22 (male)

Resistance

Between (1) – (2)

3.5 – 90 k

Between (2) – chassis ground

Min. 1 M

Disconnection in wiring har-
ness (Disconnection in wiring
or defective contact in con-
nector)

Prepare with starting switch OFF, then carry out troubleshooting
without turning starting switch ON.

Wiring harness between C01 (female) (29) –
P22 (female) (2)

Resist-

ance

Max. 1

Wiring harness between C01 (female) (46) –
P22 (female) (1)

Resist-

ance

Max. 1

Ground fault in wiring har-
ness (Short circuit with GND
circuit)

Prepare with starting switch OFF, then carry out troubleshooting
without turning starting switch ON.

Wiring harness between C01 (female) (29) –
P22 (female) (2)

Resist-

ance

Min. 1 M

Hot short (Short circuit with
24V circuit) in wiring harness

Prepare with starting switch OFF, then turn starting switch ON
and carry out troubleshooting.

Wiring harness between C01 (female) (29) –
P22 (female) (2)

Voltage

Max. 1 V

5 Defective pump controller

Prepare with starting switch OFF, then carry out troubleshooting
without turning starting switch ON.

C01 (female)

Resistance

Between (29) – (46)

3.5 – 90 k

Between (29) – chassis ground

Min. 1 M

6 Defective machine monitor

If causes 1 – 5 are not detected, machine monitor may be defective.
(Since trouble is in system, troubleshooting cannot be carried out.)

Содержание PC210-8













































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание PC210-8

Отзывы:

Похожие инструкции для PC210-8

Бренды по названию

Популярные бренды

Komatsu PC210-8, Руководство по ремонту

Результаты поиска

Содержание PC210-8

Отзывы:

Похожие инструкции для PC210-8

Бренды по названию

Популярные бренды