Komatsu PC210-8 страница 819 Скачать руководство пользователя | Manualshive

Страница: 819 / 1200

background image

40 Troubleshooting

UEN00244-02

PC210, 230, 240-8

7

Information in troubleshooting table

1

a

The following information is summarized in the troubleshooting table and the related electrical circuit
diagram. Before carrying out troubleshooting, understand that information fully.

Related circuit diagram

Trouble

Trouble which occurred in the machine

Related infor-

mation

Information related to detected trouble or troubleshooting

Possible causes

and standard

value in normal

state

Cause

Standard value in normal state/Remarks on troubleshooting

1

2

3

4

Possible causes of trouble
(Given numbers are refer-
ence numbers, which do
not indicate priority)

<Contents of description>

• Standard value in normal state to judge possible causes
• Remarks on judgment

<Troubles in wiring harness>

• Disconnection

Connector is connected imperfectly or wiring harness is bro-
ken.

• Ground fault

Wiring harness which is not connected to chassis ground cir-
cuit is in contact with chassis ground circuit.

• Hot short

Wiring harness which is not connected to power source (24
V) circuit is in contact with power source (24 V) circuit.

• Short circuit

Independent wiring harnesses are in contact with each other
abnormally.

<Precautions for troubleshooting>

1) Method of indicating connector No. and handling of T-

adapter
Insert or connect T-adapter as explained below for trouble-
shooting, unless otherwise specified.
• If connector No. has no marks of “male” and “female”, dis-

connect connector and insert T-adapters in both male side
and female side.

• If connector No. has marks of “male” and “female”, dis-

connect connector and connect T-adapter to only male
side or female side.

2) Entry order of pin Nos. and handling of tester leads

Connect positive (+) lead and negative (–) lead of tester as
explained below for troubleshooting, unless otherwise
specified.
• Connect positive (+) lead to pin No. or wiring harness

entered on front side.

• Connect negative (–) lead to pin No. or harness entered on

rear side.

This drawing is a part of the circuit diagram related to troubleshooting.
• Connector No.: Indicates (Model – Number of pins) and (Colour).
• “Connector No. and pin No.” from each branching/merging point:

Shows the ends of branch or source of merging within the parts of the
same wiring harness.

• Arrow (

): Roughly shows the location on the machine.

«
...
817
818
819
820
821
...
»

Содержание PC210-8

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PC210-8

Бренд: wsm Страницы: 19

Бренд: Gehl Страницы: 132

Бренд: Case Страницы: 292

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды