Kollmorgen - June 2014
335
MMC Smart Drive Hardware Manual
-
DRIVE RESIDENT DIGITAL MMC CONTROL
13.2
Installing the Drive Resident Digital MMC Control
13.2.1
Installing into a 230V MMC-SD Drive
1.
Remove the three screws from the right side of the cover and one screw from the
top and bottom of the drive near the front. Remove the cover.
2.
Place the cover removed in step 1 on a flat surface, with the blue plastic faceplate
down, and the large side cover to the left pointing up.
3.
Remove the two screws that hold the .6" by 8" blue filler plate to the back of the
faceplate and remove the plate.
4.
Locate the 4 screws that secure the top-most printed circuit board into the drive.
Remove one of the screws and the associated lock washer, and install one of the
four threaded standoffs that were included with the Drive Resident Digital MMC
Control (do not use the lock washer). Repeat this process for the other 3 screws,
one at a time.
5.
Place the Drive Resident Digital MMC Control into the drive, with the connectors
facing towards the front of the unit. Align the 20-pin connector on the Drive Resi-
dent Digital MMC Control with the 20-pin connector on the drive. Press the Drive
Resident Digital MMC Control onto the drive until the 20-pin connector is com-
pletely seated and the Drive Resident Digital MMC Control is seated against the
threaded standoffs installed in step 4.
6.
Fasten the Drive Resident Digital MMC Control onto the threaded standoffs using
the lockwashers and screws removed in step 4.
7.
Replace the cover using the 4 screws removed in step 1.
13.2.2
Installing into a 460V MMC-SD Drive
1.
Turn the two locking screws on the front of the drive clockwise ¼ turn and pull the
drive control board unit out of the drive.
2.
Place the drive control board unit removed in step 1 on a flat surface, with the blue
plastic faceplate down, and the drive control board to the left.
3.
Remove the two screws that hold the .6" by 8" blue filler plate and remove the
plate.
4.
Place the drive control board unit on a flat surface so that the control board is fac-
ing up, and the blue plastic faceplate is facing away from you.
5.
Locate the 4 screws that secure the top-most printed circuit board into the drive.
Remove one of the screws and the associated lock washer, and install one of the
four threaded standoffs that were included with the Drive Resident Digital MMC
Control (do not use the lock washer). Repeat this process for the other 3 screws,
one at a time.
6.
Place the control board unit on a flat surface, with the blue plastic faceplate down,
and the drive control board to the left.
7.
Loosen (but do not remove….about 2 turns) the 5 screws that hold the drive con-
trol board mounting plate to the front cover plate.
8.
Place the Drive Resident Digital MMC Control into the drive, inserting the connec-
tors on the Drive Resident Digital MMC Control through the front plate.
9.
Align the 20-pin connector on the Drive Resident Digital MMC Control with the 20-
pin connector on the drive. Press the Drive Resident Digital MMC Control onto the
Содержание MMC Smart Drive Series
