326
Kollmorgen - June 2014
MMC Smart Drive Hardware Manual
-
MAINTENANCE AND TROUBLESHOOTING
4
Drive I*t Too High
•
The product of the drives
output current multiplied
by time has exceeded
allowed limits.
•
If current foldback is
enabled the drive peak
output current
automatically reduces to
0.67% of
DIpeak
. If
foldback is not enabled,
the drive will fault.
•
Mechanically-jammed motor.
•
Motion profile acceleration requires
peak current for too long of a time
duration.
•
Machine load on the motor increased
by friction.
•
Wiring problem between drive and
motor yielding improper motion.Motor
commutation error.
•
Drive under-sized for application,
friction or load.
5
Motor I*I*t Too High
•
Motor current amplitude
squared multiplied by time
has exceed allowed limits
•
Mechanically-jammed motor.
•
Motion profile acceleration requires
peak current for too long of a time
duration.
•
Machine load on the motor increased
by friction.
•
Motor commutation error.
•
Motor under-sized for application,
friction or load.
6
Optional Battery low
•
Optional fault used to
indicate SFD battery
supply voltage is low
•
Battery low fault enabled and battery
is not installed.
•
SFD Battery backup voltage is low.
7
Bus Over Voltage - Self Re-
setting
•
The BUS voltage has
exceed the upper
threshold limit
•
AC Line voltage is too high.
•
Regenerative energy during
deceleration is causing the BUS to
rise (possible remedy: add regen
resistor).
9
Motor l-l or l-n Short
•
Line-to-Line, Line-to-
Neutral or Line-to-PE short
on the motor output
causing an instantaneous
over current.
•
Motor power wiring short circuit - line-
to-ground /neutral.
•
Motor cable short line-to-line.
•
Motor power cable length exceeds the
data sheet specification causing
excessive motor line-to-earth ground/
neutral capacitance.
•
Internal motor winding short circuit.
•
Motor L too small.
•
KIP
set too large.
Table 11-3: Drive Status LED Fault Codes (Continued)
Fault
Code
Fault
Possible Causes
Содержание MMC Smart Drive Series
