background image

Operation and Maintenance Manual

Operating fluids and maintenance

Lubricants and operating materials

Sulfur content in %

Oil change factor (factor 2)

0 < sulfur content ≤ 0.5

1

” => no change on the maintenance

interval

0.5 < sulfur content ≤ 1 limited to

lubricant category 2 and 3

1/2

” => reduces the maintenance interval

by one half

1 < sulfur content ≤ 1.5 limited to

lubricant category 2 and 3

1/4

” => reduces the maintenance interval

by one quarter. The use of sulfur in the

ratio of more than 1% requires an

additional approval of the engine

manufacturer to ensure that all engine

options, the used lubricant, and the

maintenance schedule are compatible with

this very high sulfur content. Special

lubrication oil must be used => TBN > 12

MgKOH/g.

Tab. 14: Sulfur content table

Engine oil analysis

The engine oil can be monitored by means of an engine oil analysis and the
change interval can be adjusted if required.

5.2.3  Coolant

Information

Mixing different anticorrosion antifreeze agents can make the properties of the
coolant worse.

u

Do not combine different products!

u

Silicate-based and non-silicate based coolants must never be mixed; this may
damage the cooling system!

Requirements for water

Make sure that the water used meets the following requirements:
– Fully de-ionized water should be used.
– Corresponds to the 2006 WHO (World Heath Organization) guideline for

drinking water.

The cooling circuit must remain within the following parameters:
– Hardness of water < 12 dH
– pH value 6.7 to 9.0
– Chloride and sulfate < 100 mg/l

Requirements of the coolant

Use only pre-mixed cooling water of the same kind to avoid problems with the
cooling circuit.

An SI-OAT or hybrid technology with ethylene glycol is to be used as coolant, since
this technology provides the necessary cooling performance and cooling function
for engines.

Approved products:
– BASF GLYSANTIN® G40™ change interval 6 years

KD36V16 33521029701_1_1 en 2018-08-01

© 2018 by Kohler Co. All rights reserved.

45

Содержание KD36V16















































































































Отзывы: