background image

1/16"

Number 2 Pencil

Tin Snips

3/16"

5/16"

5/16" Masonry Bit for Tile

100% Silicone Sealant

Masking Tape

32 Teeth Per Inch Blade

Miter Box

Center Punch

Hanger Bracket Kit

1205305**

Hardware Skin Pack

1203635**

1077763-A

Bolt

1199426-01**

Hanger Bracket

1044585

Roller

1051142-A

Screw

8-32 x 1/4"

#8-32 x 3/8"

1050048-B

Barrel Nut

1199110

Gasket

Model Number Label

1077762

Anchor

1031943**

Screw Cover

Top Track*

Wall Jamb 
Notch

Wall Jamb*

#8-18 x 1-1/2"

Wall Jamb 
Notch

Wall Jamb*

1131838**

Bumper

Outside Panel*

Towel Bar 
(Includes 
Hardware)*

Inside Panel*

1048208-C
1048208-F

(Silver)
(Brass)

Screw

1031943**

Screw Cover

1048208-B
1048208-K

(Silver)
(Brass)

Screw

#8-18 x 3/8" 

Bottom Track

10070.45
10070.46
10070.30
10070.72

(Silver)
(Brass)
(Nickel)
(Bronze)

Inside-Panel Guide

1017813-01**
1017813-02**
1017813-03**
1017813-05**
1017813-06**
1017813-07**
1017813-08**

(K-702200, K-702204, K-702206)
(K-702208)
(K-702202)
(K-702211, K-702221)
(K-702213)
(K-702215)
(K-702219)

A

A

"A" Mark

Cut Line

1/4" (6 mm)

Groove

x2

3

2

1

x2

x2

#8-18 x 1-1/2"

Screw Cover

Screw Cover

Bottom-Track
Leg

Notch

Correct

Incorrect

Mark

Center 
Punch

Measure distance “

A

.” Subtract 1/4” (6 mm) or 

the width of a number 2 pencil from “

A

” and cut 

the bottom track.

Position the bottom track on the center of the 
ledge. If needed, file the ends to match the 
corners.

Center the bottom track on the ledge with the 
bottom track leg to the outside. Tape the bottom 
track in place and mark the position.

IMPORTANT! The bottom track and wall jamb 
must sit flat against the shower ledge and the 
wall. 

If needed, trim and file the wall jamb. Use 

a coin to match and to transfer the corner radius 
of the shower to the wall jamb.

Position the wall jambs over the bottom track. 
Plumb both wall jambs. Mark the screw holes.

Remove the wall jambs. Drill 5/16” holes into 
the walls and insert the anchors.

Apply silicone sealant in the groove on the 
underside of the bottom track. Secure the bottom 
track to the ledge along the marked location.

Tile Installations Only

Nick the tile at the mark for the hole before 
drilling with a center punch. This keeps the drill 
bit from moving as the hole is started.
When installing to a tile wall, first drill a small 
diameter hole, then a larger hole.
Install anchors. Do not install the screws directly 
into the tile, as this may crack the tile.
When drilling, use a masonry bit.

Reposition both wall jambs. Secure the wall 
jambs with screws. Attach a bumper at the top 
and bottom locations.

Check the bumpers for the correct horizontal 
alignment with the wall jambs.

Sliding Shower and Bath Doors

Sliding Bath Doors

Sliding Shower Doors

1

1204880-2-

D

1204880-2-

D

Installation and Care Instructions

Required Tools

Parts  Identifi cation

2

3

4

7

8

6

9

5

10

K-702200, K-702202, K-702204, K-702206, K-702208, K-702211, K-702213, K-702215, K-702219, K-702221

USA/Canada: 1-800-4KOHLER
México: 001-800-456-4537

kohler.com

1

*Need help? Contact the KOHLER Customer Care Center 

at 1-800-4KOHLER (1-800-456-4537).

For service parts information, care and cleaning, and 

other information, visit www.kohler.com/serviceparts.

**Finish/color code must be specifi ed when ordering.

Retain this document for future servicing.

Record model number from box for reference.

Model Number:______________

WARNING: Risk of serious injury. 

Damage prior to installation can 

result in glass shattering. Inspect the glass and all parts for damage 
before installation.

WARNING: Risk of serious injury. 

Improper installation can result 

in glass shattering. Follow all installation instructions.

WARNING: Risk of serious injury. 

Do not cut tempered glass. 

Tempered glass will shatter if cut.

WARNING: Risk of serious injury. 

Shower door and side panels 

can shatter. Regularly inspect the glass and all parts for damage, 
missing, or loose parts.

WARNING: Risk of serious injury. 

Always wear safety glasses 

while cutting and drilling.

IMPORTANT! 

Do not touch the edges of the tempered glass with tools or 

any other hard objects. Do not set the unframed tempered glass directly on 
the floor or any hard surface.

IMPORTANT! Leave this manual for the end user.

Read these instructions before installing or using this product.

IMPORTANT! 

Do not cut the top track the same length as the bottom track.

NOTICE:

 The warranty does not apply to a product that has been modified 

or altered in a manner other than as expressly permitted in the Installation 
and Care Guide.
Walls must be within 3/8” (10 mm) of plumb.
Cover the drain with tape to avoid loss of small parts.
Follow the silicone sealant manufacturer’s instructions for application and 
curing time. 
To watch this installation online, visit the product page at 
www.kohler.com.
For care and cleaning and other information; visit 
http://www.kohler.com/clean.

Critical Information!

Read Before Installation!

Read and follow all instructions.

Содержание K-702200







Отзывы: