Kohler 6VSG Скачать руководство пользователя

Страница: 65 / 108

TP-6844 1/13

Section 5 Component Testing and Adjustment

Section 5 Component Testing and Adjustment

5.1 Theory of Operation

The generator set uses a permanent-magnet

alternator to produce 3-phase AC voltage. This

voltage is rectified using a full-wave 3-phase rectifier

(single block rectifier for 36V and 48V, three individual

rectifier blocks for 24V) to produce low-ripple DC

output. See Figure 5-1 and Figure 5-2.

The VSC measures the average DC voltage on the

output and lists this on the auto-scrolling display, in the

Overview menu and in the Generator metering menu.

Figure 5-1

Figure 5-1

Basic VSG Power Connections

Figure 5-2

Figure 5-2

Output Waveform, with Rectified Signal

The voltage is regulated to maintain a constant output

voltage, which is equal to the System Voltage setting.

When the load on the 6VSG generator increases, the

generator controller increases the engine speed. The

6VSG series is designed to produce rated voltage at

2300 rpm with no load and at 2900 rpm when

supplying full load. The output current and power

increase with the engine speed. The engine speed is

limited to a maximum of 2900 rpm. See Section 3.3.1

for more information.

5.2 Electrical Output

Troubleshooting

5.2.1 No to Low Voltage Operation

This section covers the operation of the electrical

output and troubleshooting information for low or no

voltage output. Before beginning the test procedures,

read all safety precautions at the beginning of this

manual. Many of the test procedures include

additional safety precautions.

If the output voltage is below 85% of the rated voltage

at no load, check the following with the engine running

(press RUN to start the generator set):

• The output breaker is closed (check voltage at the

rectifier).

• The Voltage Regulator Average Voltage Adjustment

parameter is correct.

• Engine Speed (should be within 300 rpm of the idle

speed) – if the engine speed is low, check the

voltage and % load reading on the VSC controller.

High current means a short circuit; rated voltage

indicates that the VSC controller sees the correct

voltage.

KPS_105

KPS_106

Содержание 6VSG













































































































Результаты поиска

Содержание 6VSG

Отзывы:

Похожие инструкции для 6VSG

Бренды по названию

Популярные бренды

Kohler 6VSG, Руководство по обслуживанию

Результаты поиска

Содержание 6VSG

Отзывы:

Похожие инструкции для 6VSG

Бренды по названию

Популярные бренды