Kohler 6VSG Скачать руководство пользователя

Страница: 85 / 108

TP-6844 1/13

Section 6 Disassembly/Reassembly

Section 6 Disassembly/Reassembly

This section provides instructions for the disassembly

and reassembly of the generator set alternator. Before

beginning the generator disassembly or reassembly

procedure, carefully read all safety precautions at the

beginning of this manual.

The engine and generator set may use both American

Standard and metric hardware. Use the correct size

tools to prevent rounding of the bolt heads and nuts.

Disabling the generator set. Accidental starting can

cause severe injury or death.

Before working on the

generator set or equipment connected to the set, disable the

generator set as follows: (1) Press the generator set

off/reset button to shut down the generator set. (2)

Disconnect the power to the battery charger, if equipped. (3)

Remove the battery cables, negative (–) lead first.

Reconnect the negative (–) lead last when reconnecting the

battery. Follow these precautions to prevent the starting of

the generator set by the remote start/stop switch.

6.1 Initial Steps

Perform the following steps before disassembling the

generator set.

1. Disconnect power to the generator set.

2. Shut off the fuel supply. Disconnect the fuel

system if necessary to tilt the generator set.

Ventilate the area to clear fumes.

3. Allow the generator set and engine to cool.

4. Verify that any hoists or lifting devices used in the

disassembly or reassembly procedure are rated

for the weight of the generator set, which is

approximately 190 kg (420 lb.).

6.2 Disassembly

The disassembly procedure explains how to

disassemble the generator set enclosure and other

parts in order to access the alternator for service. The

procedure provides important information to minimize

disassembly time and indicates where special

configurations exist which may require taking notes.

Remove Enclosure

Remove the generator set enclosure as described in

the following steps. See Figure 6-1.

1. Open the front service door.

2. Press the OFF button on the controller.

3. Lift off roof and slide toward exhaust end to

disengage tabs from slots. Remove ground strap

if necessary.

WARNING

Accidental starting.

Can cause severe injury or death.

Disconnect the battery cables before

working on the generator set.

Remove the negative (–) lead first

when disconnecting the battery.

Reconnect the negative (–) lead last

when reconnecting the battery.

DANGER

Hazardous voltage.
Will cause severe injury or death.

Disconnect all power sources before

opening the enclosure.

WARNING

Hot engine and exhaust system.

Can cause severe injury or death.

Do not work on the generator set

until it cools.

Содержание 6VSG













































































































Результаты поиска

Содержание 6VSG

Отзывы:

Похожие инструкции для 6VSG

Бренды по названию

Популярные бренды

Kohler 6VSG, Руководство по обслуживанию

Результаты поиска

Содержание 6VSG

Отзывы:

Похожие инструкции для 6VSG

Бренды по названию

Популярные бренды