Kohler 6VSG Скачать руководство пользователя страница 13

Страница: 13 / 108

TP-6844 1/13

Section 1 Specifications

Section 1 Specifications

1.1 Introduction

The specification sheets for each generator set

provide specific generator and engine information.

Refer to the generator set specification sheet for

ratings and other data not supplied in this manual.

Consult the generator set installation manual, engine

operation manual, and engine service manual for

additional specifications.

Consult the generator set nameplate for specific

generator set ratings.

1.2 Controller Specifications

Model 6VSG generator sets are equipped with the

VSC controller. For a specific description of the

controller, see the generator set operation manual.

Figure 1-1

Figure 1-1

Controller Specifications

1.3 Engine Service

Generator sets covered in this manual are equipped

with four-cycle, twin cylinder, air-cooled Kohler

engines.

For engine service information and specifications not

covered in this manual, see the engine service

manual. See the List of Related Literature in the

Introduction section.

1.4 Engine Specifications

Figure 1-2

Figure 1-2

Engine Specifications

Environmental Specification

All Models

Operating temperature

-30 to 70°C

Storage temperature

-40 to 85°C

Humidity

0–95% condensing

Power requirements:

Voltage

12 VDC

Current (standby state)

250 mA @ 12 VDC

Engine Specification

6VSG

Manufacturer

Kohler

Model

CH740

Cycle

Number of cylinders

Compression ratio

9:1

Displacement, cc (cu. in.)

725 (44)

Rated power, propane fuel,

kW (HP)

The engine max

horsepower at 2900 rpm is

~21.2LPG and 18.5NG.

This unit is underrated by

limiting current to 6 kW.

Rated power, natural gas,

kW (HP)

Rpm, No load

2300

Rpm, Full load

2900

Bore x stroke, mm (in.)

83 x 67 (3.27 x 2.64)

Valve material

Steel/Stellite

Cylinder block material

Aluminum w/cast iron liners

Cylinder head material

Aluminum

Piston rings

2 compression/ 1 oil

Crankshaft material

Heat-treated ductile iron

Main bearings: number, type

2, parent material

Lubrication system

Full pressure

Oil capacity (w/filter), L (qt.)

1.9 (2.0)

Oil pressure, kPa (psi)

172–241 (25–35)

Fuel system

LPG or natural gas

Minimum fuel supply

pressure, kPa (in. H

LPG and NG: 1.2–2.7 (5–11)

Battery voltage

12 VDC

Battery ground

Negative

Spark plug gap, mm (in.)

0.76 (0.030)

Ignition system

Capacitor discharge

Starter motor

Electric, solenoid shift

Cooling system

Air-cooled

Содержание 6VSG













































































































Результаты поиска

Содержание 6VSG

Отзывы:

Kohler 6VSG, Руководство по обслуживанию, Страница: 13 / 108

Результаты поиска

Содержание 6VSG

Отзывы: