Kohler 6VSG Скачать руководство пользователя

Страница: 28 / 108

Section 3 Controller

TP-6844 1/13

Figure 3-3

Figure 3-3

USB Connection

3.3 Controller Parameters

Adjustable parameter settings can be changed using a

personal computer (or laptop) with Kohler SiteTech

software. See Section 3.2, SiteTech and OnCue

Software for USB connection information. See the

SiteTech Operation Manual, TP-6701, for general

software operation instructions.

Some parameter settings can also be changed at the

VSC controller. See the generator set operation

manual for instructions to navigate through the

controller menus and change settings.

3.3.1 Genset System Menu

The genset system menu displays the system

information shown in Figure 3-4. Generator sets are

factory-set and should not require changes to the

system settings in the field.

A Kohler-authorized distributor or dealer can adjust

these settings, if necessary. If the system settings

require adjustment, see Installation Manual for

instructions.

Note:

Use caution when navigating the controller

menus. In some menus, pressing the Select

button can enable editing of the controller

settings. Changing the settings to incorrect

values can adversely affect generator set

operation or render the unit inoperable.

System Parameters for Battery Bank Charging

The following system parameters can be viewed in the

Genset System menu on the user interface on the

generator set’s VSC controller.

• System Voltage

• Auto Start Voltage

• Auto Stop Load (%)

• Load Limit

Note:

Changing these settings can damage your

generator set and batteries. Always refer to the

information provided by the battery bank

manufacturer for the correct voltage and charge

current limits for your batteries. See the

Operation Manual for instructions to change

settings, if necessary.

KPS_065

1. USB cable connection to PC

2. USB cable connection to controller

Содержание 6VSG













































































































Результаты поиска

Содержание 6VSG

Отзывы:

Похожие инструкции для 6VSG

Бренды по названию

Популярные бренды

Kohler 6VSG, Руководство по обслуживанию

Результаты поиска

Содержание 6VSG

Отзывы:

Похожие инструкции для 6VSG

Бренды по названию

Популярные бренды