Kohler 6VSG Скачать руководство пользователя

Страница: 27 / 108

TP-6844 1/13

Section 3 Controller

Section 3 Controller

3.1 Introduction

The VSC controller manages the operation of the

generator set and the optional Programmable

Interface Module (PIM). See the generator set

Operation Manual for controller operation instructions.

This section covers adjustment and replacement of the

VSC controller. See Section 4.10 for troubleshooting

information.

The VSC controller is shown in Figure 3-1. See the

service view, Figure 1-6, for the controller location.

Figure 3-1

Figure 3-1

VSC Controller

3.2 SiteTech and OnCue Software

Many procedures in this manual require the use of a

personal computer (or laptop) with Kohler

SiteTech™

software to change controller settings or update

firmware. SiteTech software is available to

Kohler-authorized distributors and dealers. See the

SiteTech Operation Manual, TP-6701, for general

software operation instructions.

Some procedures can be also performed using

Kohler

OnCue

software if the controller is

connected to the computer with a USB cable. See

Figure 3-3.

Use a USB cable to connect the personal computer

directly to the device. See Figure 3-3. The USB cable

must have a male USB A connector on one end and a

male mini-B connector on the other and must be less

than 5 m (16.4 ft.) long. See Figure 3-2.

Figure 3-2

Figure 3-2

USB Cable

KPS_048
GM77569

KPS_066

1. Detail, mini-B connector

Содержание 6VSG













































































































Результаты поиска

Содержание 6VSG

Отзывы:

Похожие инструкции для 6VSG

Бренды по названию

Популярные бренды

Kohler 6VSG, Руководство по обслуживанию

Результаты поиска

Содержание 6VSG

Отзывы:

Похожие инструкции для 6VSG

Бренды по названию

Популярные бренды