Kohler 6VSG Скачать руководство пользователя

Страница: 64 / 108

Section 4 Troubleshooting

TP-6844 1/13

4.10 Controller Troubleshooting

Refer to the controller troubleshooting table in

Figure 4-5 when troubleshooting procedures in

Section 4.9 indicate a possible controller problem.

Also check the controller display for fault messages

and see Section 4.7, Fault Messages.

Always check the controller settings before replacing

the controller. VSC controller settings can be checked

and adjusted through the controller’s user interface or

using a personal computer and Kohler SiteTech

software. The generator set operation manual

contains the instructions for checking and changing

the controller settings. See TP-6701, SiteTech

Software Operation Manual. Kohler SiteTech software

is available to authorized distributors and dealers.

Figure 4-5

Figure 4-5

VSC Controller Troubleshooting

Problem

Possible Cause

Corrective Action

Reference

Controller LCD

display is off.

Low or no battery voltage

Check controller connections.

W/D Section 7

Check DC power to the VSC

controller.
Check generator set battery

connections and condition.
Check power connection to the

generator set terminal block

(power for battery charging). (if

equipped)

Controller display

backlight is off.

Backlight turns off after about

1 minute with no activity

Backlight will turn on when a

button is pressed or the

generator set starts.

—

Loss of

communication to

accessory modules.

Bad connections

Check wiring and connections.

Verify that cable size and length

of run comply with the

instructions in the Installation

Manual.

Generator set Installation

Manual or accessory module

documentation

Communication cable does not

meet required specifications

Use shielded, twisted-pair cable

as specified in the Installation

Manual. Do not exceed the

maximum cable lengths given in

the Installation Manual.

Installation Manual

Low or no battery voltage

Check generator set battery

connections and condition.

—

See “Low or no battery voltage”

above.

Date is flashing.

Controller power was

disconnected and then

reconnected

Check battery connections.
Check controller connections.

W/D Section 7

Check power connection to the

generator set terminal block.
Reset the time, date, and

exercise schedule.

Generator set O/M

Cannot change input

and output settings.

Controller is set up for the optional

communications kit, which locks

the input and output settings.

For a generator set with a

communications kit, no action is

needed. Inputs and outputs are

not adjustable.

If the generator set is connected

to a PIM, use SiteTech to

change the Personality Installed

Option parameter setting.

Section 3.3.3, Digital Inputs and

Outputs, and Section 3.3.4,

Controller Parameter Table

Содержание 6VSG













































































































Результаты поиска

Содержание 6VSG

Отзывы:

Похожие инструкции для 6VSG

Бренды по названию

Популярные бренды

Kohler 6VSG, Руководство по обслуживанию

Результаты поиска

Содержание 6VSG

Отзывы:

Похожие инструкции для 6VSG

Бренды по названию

Популярные бренды