Kohler 10EKD-Low CO Скачать руководство пользователя

Страница: 41 / 52

TP-6591 10/13

Section 5 Wiring Diagrams

Section 5 Wiring Diagrams

Accidental starting.

Can cause severe injury or death.

Disconnect the battery cables before

working on the generator set.

Remove the negative (--) lead first

when disconnecting the battery.

Reconnect the negative (--) lead last

when reconnecting the battery.

WARNING

Disabling the generator set. Accidental starting can

cause severe injury or death.

Before working on the

generator set or equipment connected to the set, disable the

generator set as follows:

(1) Place the generator set

start/stop switch in the STOP position. (2) Disconnect the

power to the battery charger, if equipped. (3) Remove the

battery cables, negative (--) lead first. Reconnect the negative

(--) lead last when reconnecting the battery. Follow these

precautions to prevent the starting of the generator set by the

remote start/stop switch.

Hazardous voltage.

Can cause severe injury or death.

Operate the generator set only when

all guards and electrical enclosures

are in place.

Moving parts.

WARNING

Grounding electrical equipment. Hazardous voltage can

cause severe injury or death.

Electrocution is possible

whenever electricity is present. Ensure you comply with all

applicable codes and standards. Electrically ground the

generator set, transfer switch, and related equipment and

electrical circuits. Turn off the main circuit breakers of all

power sources before servicing the equipment. Never contact

electrical leads or appliances when standing in water or on wet

ground because these conditions increase the risk of

electrocution.

Содержание 10EKD-Low CO





















































Результаты поиска

Содержание 10EKD-Low CO

Отзывы:

Похожие инструкции для 10EKD-Low CO

Бренды по названию

Популярные бренды

Kohler 10EKD-Low CO, Операция

Результаты поиска

Содержание 10EKD-Low CO

Отзывы:

Похожие инструкции для 10EKD-Low CO

Бренды по названию

Популярные бренды