Kodak Prostar Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 45

background image

A-62051 May 2008

9

Installing the processing
racks

1. Make sure that the rollers of each rack turn freely when you rotate

the drive gear.

2. Drain off any excess water if the racks were left submerged in water

since the last time film was processed.

3. Hold the gear cover back and lower the processing racks into the

processor (#6 rack first, then #5, #4, #3, #2, and #1).

The rack number is located just above the drive gear.

CAUTION: Lower the racks slowly and carefully into the

Archive Processor to avoid splashing any chemicals.

Installing the dryer rack

1. Lift off the dryer section cover.

2. Make sure that the rollers of the dryer rack turn freely when rotating

the drive gear.

3. Pull the gear cover back and lower the dryer rack into the dryer

section.

4. Replace the dryer section cover.

Rack #6

Gear Cover

Gear Cover

Dryer Rack (#7)

Dryer Section Cover

«
...
11
12
13
14
15
...
»

Содержание Prostar














































Отзывы:

Нет отзывов

Похожие инструкции для Prostar

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 31

Бренд: Samsung Страницы: 15

Бренд: Yaesu Страницы: 2

Бренд: Furuno Страницы: 24

Бренд: Amplifier Tech Страницы: 36

CLICK PLUS C2-02CPU

Бренд: Automationdirect.com Страницы: 10

Бренд: Renesas Страницы: 941

Optane Persistent Memory 200 Series

Бренд: Supermicro Страницы: 54

Бренд: ZALMAN Страницы: 7

EK-FC980 GTX Classy

Бренд: ekwb Страницы: 2

Бренд: Renesas Страницы: 4

Бренд: ADTRAN Страницы: 2

Бренд: Aim Страницы: 35

ExtremeCloud Appliance E1120

Бренд: Extreme Networks Страницы: 219

Бренд: Thecus Страницы: 148

Бренд: ZALMAN Страницы: 12

Бренд: Commax Страницы: 122

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды