background image

3

Cautions for Use

Things You Need to Know

Videophone

Cautions

Cautions for Abnormality

Safety Instructions, Warnings and Cautions of Each System

·This product is designed as a home videophone and cannot use continuously like monitor camera.           
·If there is temperature difference between inner part of camera and surrounding, dew condensation occurs on camera lens and may disturb image.  
   If dew condensation is removed from camera lens, image quality recovers.  
·White LED light examination range is narrower than camera shot range at night, so there is less amount of light at night than day.   
   So it is difficult to see the face in low illumination condition due to noise increase on screen, but it is not from defect.  
·Monitor screen (liquid crystal panel) is not in defect when some pixels always light or black out.     
·Please install monitor and camera over 5cm away.  
   Also, avoid installing at a place with too much noise, because too much noise around camera causes phone call inferiority.
·Do not place an object within 20cm in front of monitor. It causes phone call inferiority, especially because microphone is installed at the top of monitor. 
·If strong light such as sunlight flows into camera module, screen saturation (or strange mark) and image shaking might occur.
·This is not a defect, so please do not install camera where a direct ray of light do not flow if possible.

·Separate the AC/DC wire with the hook of the wall-mounted type when installing.   쪾       ·Connect the wire after peeling the wires properly.
·Do not distribute signal line with AC line.                                                                   ·Use the designed driver to connect the wire to terminal.
·Do not clean the LCD with the damp cloth for cleaning. Use the only dry and soft cloth.      ·Do not install the main gate monitor at the leaking place.

·In some cases there is occurrence of product destruction, malfunction, noise mixing and picture quality deterioration due to mixing of other tool's
   induced. voltage or thunder with communication wiring of monitor/camera, monitor/extended monitor.
   Do not wire with power line such as outdoor wiring or AC power, or phones and other tools.                      
·You cannot use it if you incorrectly wire the AC voltage between monitor/camera, monitor/extended monitor. 
   Call the store or agency where you purchased this product and consult to solve the problem.
   Beware that unfixable damage might be caused due to authorizing AC voltage on communication wiring of monitor/camera, monitor/extended monitor.   
·Do not ever disjoint this product.  It may cause electrocution accident when touching high-voltage circuit inside this product.                      
·Outside power authorizing this product must be confirmed of product description and use rated voltage.
   Beware that if higher voltage is authorized, unfixable damage might be caused due to product destruction.                     
·Power must be connected to domestic voltage (product rated voltage) consent or interior wiring.
   If connected to other motive power or inverter-type power, product destruction, noise mixing, and picture distortion may occur.    
·Do not drop this product. Glass is used for monitor and might break, or cause other circuit inferiority.
   In such case, immediately turn down the power switch, and call to consult agency or store in which this product was purchased.                     
·Keep away from any conditions where water splatters or falls. Do not place anything containing water like a vase on the product.
·If you install a product nearby an antenna used for broadcast media, image could be distorted or mixed with a voice so that it is likely not to work
   properly in some functions.                      
·Avoid installing near tools with strong electromagnetic waves such as microwaves and cell phones, as it may cause a picture distorted or a voice with
   a noise. In that case, the product is likely not to work properly in some functions.                    
·Do not install monitor in following places. 
   ① Above or around water heater, rice-cooker, heater          ② Place exposed to direct rays of the sun
   ③ Place with temperature below 0'C such as cold store        ④ Place with high humidity such as bathroom, washroom, heated room                            
   ⑤ Place with a lot of gas, dust, smoke                              ⑥ Dangerous place with sprays of water or chemicals
·Do not wipe with insecticide, drugs or chemicals such as thinner and alcohol, or it may damage 
   the surface of this product.        
·Beware of occurrence of image quality deterioration or malfunction from cause of humidity due to 
   penetration of chemicals or water into camera’s urea resins. 
·As in the picture, it prevents temperature difference of camera (outside) and monitor (inside), and 
   removes dew condensation caused by humidity of camera window.           
·Camera must be installed when wall cement is completely dry.           
·When product is installed in winter below -5'C, wait for approximately 2 hours to connect. Dew formation 
   in monitor and camera due to temperature difference inside and outside may cause product defect.           
·Avoid installing monitor and camera in place directly exposed to heat or where gas noxiousness is highly occurring.

·Do not disassemble this unit at will as this device is composed by precision parts.   쪾   ·Install the unit by following the set-up instructions of Kocom.
·Do not touch or insert any foreign substances, for example, sticker, magnetic, opener and the like.
·Make U-type at the end of wires as the rain can effect on the system by following the wires during the rainy season. 

·This unit is not designed for security purpose.     쪾·Do not handle the unit with the wet hands.
·Do not place a pot with water or a small metal material on the Units.
·Do not cover the ventilating opening or put any metal material in the units. 쪾
·During thunderstorms, avoid using this unit. There may be a remote risk of an electric shock from lighting. 
·Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void user`s authority to operate the equipment.                          

·Change the damaged electric code. 
·Unplug this unit from plug socket and refer servicing to an authorized service center when the following conditions occur:
·If liquid has been spilled into the unit.                      쪾·If the unit does not work normally by following the operating instructions.
·If the unit exhibits a distinct change in performance.      ·If the unit has been dropped or physically damaged.

·Do not disassemble the back and cabinet cover.

Tapón de la tubería de PCV con

sustancias adiabáticas para

prevenir la circulación del aire

Caja con

tubería

Monitor

Tubería

Cámara

(Exterior, Puerta)

Caution

Содержание KCV-T701SM





























Отзывы: