Kobold DON-05 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 48

Kobold DON-05 Скачать руководство пользователя страница 33

DON-H

DON-H

01/0721

page 33

15.1.4

Servicing, maintenance

Definition of terms according to IEC 60079-17:

Maintenance and repair:

A combination of all activities carried out in order to

keep an object in a condition or to bring it back into a condition that meets the
requirements of the relevant specification and ensures the execution of the
required functions.

Inspection:

An activity that involves the careful examination of an object with the

aim of making a reliable statement about the condition of this object, without
dismantling or, if necessary, with partial dismantling, supplemented by measures
e.g. measurements is carried out.

Visual inspection:

A visual inspection is an inspection in which visible defects

are found (e.g. missing screws) without the use of devices or tools.

Close-up inspection:

An inspection that, in addition to the aspects of the visual

inspection, identifies defects such as loose screws that can only be removed
through the use of access devices (e.g. if necessary stairs) and tools. For close-
up tests, a housing usually does not need to be opened or the equipment needs
to be de-energized.

Detailed inspection:

An inspection in which, in addition to the aspects of close-

up inspection, defects such as loose connections, which can only be identified by
opening housings and / or, if necessary, using tools and testing equipment, are
treated.

Maintenance measures may only be carried out by qualified persons.

Only accessories that meet all the requirements of the European directives and
national legislation may be used in potentially explosive areas.

Maintenance measures including dismantling the flow meter may only be

carried out in a non-explosive atmosphere.
  Components  may  only  be  replaced  with  original  spare  parts  that  are  also
approved  for  use  in  Ex  areas.  Repairs  only  by  the  manufacturer  or  specialist
workshop.
  The  products  must  be  regularly  serviced  and  cleaned  in  the  Ex  area.  The
intervals  are  determined  by  the  operator  in  accordance  with  the  environmental
stresses on site.

Activity

Visual

inspection

per month

Close-up

inspection

every 6 months

Detailed

inspection

every 12

months

1

Visual inspection of the flow
meter for damage and remove
dust deposits

●

2

Check for integrity and function

●

3

Examination of the entire
system

In the operator's area of responsibility

«
...
31
32
33
34
35
...
»

Содержание DON-05

















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды