KNOVA KN M-3059R, Руководство пользователя

Страница: 10 / 64

Cutting
head
#8
Hold-down latch
#4
Switch
handle
#1
Miter
handle
#6
Positive stop
locking lever
#7
Positive
stop bolt
#3
Safety
lock pin
#5
Detent
block
Carrying handle
#2
Bevel lock
handle
Fig. B
Fig. A
ASSEMBLY
9
Remove saw from support base. Place saw with blade and
fence side facing up on a flat, stable surface. (Fig. A)
STEP 1: Thread the miter handle (1) into the hole located at
the front of the table as shown in Figs. B & C.
STEP 2: Loosen the bevel lock handle (2) located behind the
base as shown in Figs. A & D.
STEP 3: Pull out the red safety lock pin (3) located next to the
bevel lock handle as shown in Fig. D.
STEP 4: Grasp the cutting head by the switch handle (4)
Fig B and raise head up to vertical position just
past the 0° bevel setting. The pin will automatically
insert into the slot, locking the head into position.
STEP 5: Rotate the metal detent block (5), located on the
right side behind the table (Figs. B & E),
counterclockwise 180°.
Fig. C
Fig. D
Fig. E Fig. F
8
7
5
2
3
1
6
LOCKING THE CUTTING HEAD (FIG. B, F)
When not in use, the miter saw cutting head should always be
locked in the down position.
FOLDING THE CUTTING HEAD FOR TRANSPORTATION
AND STORAGE (FIG. A, B)
NOTE: Remove the hold-down clamp assembly (1, Fig. H)
from saw before folding and transporting.
1. Raise the cutting head all the way up.
2. Slightly push down the switch handle (4) and push the
hold-down latch (8) into the locking hole. (Figs. A & B)
3. Loosen the miter handle (1), grasp it and lift up the positive
stop locking lever (6) to turn the turntable to the right to
60° as shown on the miter scale. Then tighten the miter
handle. (Fig. B)
1. Pull down the switch handle (4) to place the cutting head in
its lowest position.
2. Push the hold-down latch (8) in.
NOTE: Make sure power cord is wrapped up securely
before folding the saw for storage or transport.
IMPORTANT: To avoid damage, never carry the miter saw by
the lower blade guard, the switch handle, the cutting head or
the miter handle. ALWAYS use the designated carrying
handle. (See Figs. B & O)
WARNING
• To reduce the risk of injury, you must
unplug the saw from power source before folding
for transportation or storage.
• To reduce the risk of injury, turn unit off and disconnect
it from power source before installing and removing
accessories, before adjusting or when making repairs.
An accidental start-up can cause injury.
• Make sure blade has stopped rotating before folding
the saw.
STEP 6: Tilt the cutting head back to 0° and then tighten the
bevel lock handle (2). The positive stop bolt (7)
Fig E will now rest on the detent block (5).
STEP 7: Loosen the miter handle (1), grasp it and lift up the
positive stop locking lever (6) (Figs. B &C) located
under the miter handle, to turn the table to 0° as
shown on the miter scale. Retighten the miter
handle (1).
STEP 8: Grasp switch handle (4) and slightly push down on
the cutting head. With other hand pull out the
hold-down latch (8) (Fig. F) located near the back on
the left side of saw. This releases the cutting head
from locked position to swing upward into operation
position.