KNOVA KN M-3059R, Руководство пользователя

Страница: 6 / 64

5
ELECTRICAL REQUIREMENTS AND SAFETY
GUIDELINES FOR EXTENSION CORDS
Use a proper extension cord. Make sure your extension cord
is in good condition. When using an extension cord, be sure
to use one heavy enough to carry the current your product
will draw. An undersized cord will cause a drop in line voltage,
resulting in loss of power and cause overheating. The table
below shows the correct size to use depending on cord length
and nameplate ampere rating. If in doubt, use the next heavier
gauge. The smaller the gauge number, the heavier the cord.
Be sure your extension cord is properly wired and in good
condition. If it is not, replace it with another cord. Do not use
a damaged extension cord. Protect your extension cords from
sharp objects, excessive heat and damp or wet areas.
Use a separate electrical circuit for your tools. This circuit
must not be less than a #12 wire with a 16 A time-lag fuse or
a #14 wire with a 12 A time-lag fuse.
NOTE: When using an extension cord on a circuit with a #14
wire, the extension cord must not exceed 25 feet in length.
TOOLS NEEDED TO REMOVE OR INSTALL BLADE
ACCESSORIES AND ATTACHMENTS
RECOMMENDED ACCESSORIES
WARNING
• Use only accessories recommended for this
miter saw. Follow instructions that accompany accessories.
Use improper accessories may cause hazards.
• The use of any cutting tool except 12 in. saw blades which meet
the requirements under recommended accessories is prohibited.
Do not use accessories such as shaper cutters or dado sets.
Ferrous metal cutting and the use of abrasive wheels is prohibited.
• Do not attempt to modify this tool or create accessories not
recommended for use with this tool. Any such alteration or
modification is misuse and could result in a hazardous condition
leading to possible serious injury.
ACCESSORIES
Visit your Knova Hardware Department or see the Knova Power and
Hand Tool Catalog to purchase recommended accessories for this
power tool.
WARNING
• To avoid the risk of personal injury, do not
modify this power tool or use accessories not recommended
by Knova.
• Read warnings and conditions on your CARBIDE TIPPED SAW
BLADE. Do not operate the saw without the proper saw blade
guard in place. Carbide is a very hard but brittle material. Care
should be taken while mounting, using, and storing carbide tipped
blades to prevent accidental damage. Slight shocks, such as
striking the tip while handling, can seriously damage the blade.
Foreign objects in the workpiece, such as wire or nails, can also
cause tips to crack or break off. Before using, always visually
BLADE INFORMATION
• Always use a crosscut blade that is designed for cutting across
grain. NEVER use Rip, Combination, Plywood, Dado or
Abrasive type saw blades at any time.
• Always use a 12 in. diameter blade with either a 1 in. arbor
hole, speed rating must be at least 4000 RPM.
• Read and understand all instructions provided with each blade
before using on this miter saw.
There are two main materials used for saw blades; high-speed steel
(HSS) and carbide tipped (TCT). While the HSS blades are generally
less expensive than carbide tipped, TCT blades will stay sharper
longer than HSS. As a general rule the more teeth per inch (TPI) the
smoother the cut. Please read the information provided on the blade
for more details for their use.
General Purpose Wood Cutting: 24 - 40 TPI
Fine Woodworking Cutting: 60 - 80 TPI
Non-ferrous Metal Cutting: Use only special blades designed for
cutting this type of material.
Plastic Cutting:
Use only special blades designed for cutting plastic.
NOTE: When cutting non-ferrous or plastic, be sure to clean up
completely after each use. Take special care with metal shavings
after each cut, these can cause damage to the table top.
ALWAYS WEAR EYE PROTECTION.
MINIMUM GAUGE FOR EXTENSION CORDS (AWG)
(When using 120 volts only)
Ampere Rating Total length of Cord
More than
Not more than
25ft. 50ft. 100ft. 150ft.
0 6 18 16 16 14
6 10 18 16 14 12
10 12 16 16 14 12
12 16 14 12 Not Recommended
In all cases make certain the receptacle
in question is properly grounded. If you are not sure,
have a certified electrician check the receptacle.
CAUTION
Before connecting the tool to the power line, make sure the
switch is in the OFF position and the electric current is rated
the same as the current stamped on the motor nameplate,
running at a lower voltage will damage the motor.
examine the blade and tips for bent blade, cracks, breakage,
missing or loose tips, or other damage. Do not use if damage is
suspected. Failure to heed safety instructions and warnings can
result in serious bodily injury.
TOOLS NEEDED FOR ADJUSTMENT
SUPPLIED
Blade Wrench
NOT SUPPLIED
Adjustable Wrench
Combination Square
Phillips Screwdriver
Slotted Screwdriver