DANGER
Table of contents .............................................................. 1
Product specifications ....................................................... 1
Warnings ........................................................................... 1
Symbols ............................................................................. 1
Power tool safety .............................................................. 2
Compound miter saw safety ............................................. 3
Electrical requirements and safety .................................... 4
Accessories and attachments ........................................... 5
Tools needed for assembly ............................................... 5
Carton contents ................................................................ 6
Know your slide compound miter saw ............................... 7
Glossary of terms .............................................................. 8
Assembly ........................................................................... 9
Adjustments ..................................................................... 13
Operation ........................................................................... 17
Maintenance ...................................................................... 26
Troubleshooting guide ....................................................... 27
Parts list ............................................................................ 28
Diagram parts .................................................................... 30
Parts list and motor diagram ............................................. 31
PRODUCT SPECIFICATIONS
MOTOR
Power Source:
120V AC, 60Hz, 15 Amp
Arbor Shaft Size:
5/8 in.
Speed (no load):
4800 RPM (No load)
Electric Brake:
Yes
Double Insulated:
Yes
TABLE OF CONTENTS
1
SYMBOLS
WARNING
WARNING ICONS
Your power tool and its Instruction Manual may contain “WARNING ICONS” (a picture symbol intended to alert you to, and/or
instruct you how to avoid, a potentially hazardous condition). Understanding and heeding these symbols will help you operate
your tool better a. safer. Shown below are some of the symbols you may see.
SAFETY ALERT
: Precautions that involve your safety.
PROHIBITION
WEAR EYE PROTECTION
: Always wear safety
goggles or safety glasses with side shields.
READ AND UNDERTAND INSTRUCTION MANUAL
:
To reduce the risk of injury, user and all bystanders
must read understand instruction manual before using
this product.
KEEP HANDS AWAY FROM BLADE
: Failure to
keep your hands away from the blade will result
in serious personal injury.
SUPPORT AND CLAMP WORK
DANGER
: Indicates an inminently
hazardous situation which, if not avoided, will result
in death or serious injury.
WARNING
: Indicates a potentially
hazardou situation which, if not avoided, could result
in dead or serious injury.
CAUTION
: Indicates a potentially hazardou
situation which, if not avoided, may result in minor or
moderate injury.
CAUTION
: Used without the safety alert
symbol indicates a potentially hazardous situation which,
if not avoided, may result in property damage.
BLADE
Diameter:
10 in.
Arbor hole:
5/8 in.
MITER SAW
Miter detent stops:
0º, 15º, 22.5º, 31.6º, 45º R & L
Bevel positive stops:
0º, 33.9º, 45º R & L
WARNING
To avoid electrical hazards, fire hazards or damage to the tool, use proper circuit protection. This tool
is wired at the factory for 110-120 Volt operation. It must be connected to a 110-120 Volt / 15 Ampere time delay
fuse or circuit breaker. To avoid shock or fire, replace power cord immediately if it is worn, cut or damaged in any way.
Before using your tool, it is critical that you read and understand these safety rules. Failure to follow these rules could result
in serious injury to you or damage to the tool.
WARNING
CAUTION
CAUTION
CUTTING CAPACITY
Crosscut (with the stop plate):
3-1/2 in. x 11-1/2 in.
Crosscut (without the stop plate):
2-1/2 in. x 12-1/2 in.
Miter 45° R & L (with the stop plate):
3-1/2 in. × 8 in.
Miter 45° R & L (without the stop plate):
2-1/2 in. × 8-3/4 in.
Bevel 45º Left (with the stop plate):
1-3/4 in. x 11-1/2 in.
Bevel 45º Left (without the stop plate):
1-5/8 in. x 12-1/2 in.
45° Miter and 45° bevel left (with the stop plate):
1-3/4 in. x 8 in.
45° Miter and 45° bevel left (without the stop plate):
1-5/8 in. x 8-3/4 in.
Crown molding nested:
5-3/4 in.
Base molding against fence:
3-1/2 in.
Содержание KN M-2509RC
Страница 1: ...KN M 2509RC Slide compound miter saw10 Sierra angular compuesta deslizable 254 mm...
Страница 31: ...30 DIAGRAM PARTS Slide compound miter saw10 Sierra angular compuesta deslizable 254 mm KN M 2509RC...
Страница 62: ...DIAGRAMA DE PARTES 61 Slide compound miter saw10 Sierra angular compuesta deslizable 254 mm KN M 2509RC...
Страница 64: ...www knova com mx...
