17
ADJUSTMENTS
EXTENSION WING USE AND ADJUSTMENT
(FIG. AA)
The left and right side extension wings can offer extra support
for long workpieces.
1. Lift up on the locking lever (1) and pull out the left extension
wing to the desired support length. Push down on the locking
lever (1) to tighten the extension wing. Repeat for the right
side extension wing if needed.
2. If the locking lever (1) will not tighten, adjust the nut (2), located under
the base, 1/4 turn clockwise using a 10 mm wrench until tight.
REPETITIVE CUTTING USING THE STOP PLATE
(FIG. AA)
The stop plate is designed for making repetitive cuts of the same length.
NOTE
: Use only one stop plate at a time, NEVER use both stop plates.
1. Rotate the stop plate (3) to vertical position.
2. If stop plate will not rotate, loosen the locking screw (4) 1/4 turn using
a screwdriver and 8 mm wrench.
• Completely assemble and adjust the saw, following
the instructions.
(ASSEMBLY & ADJUSTMENTS)
• Learn
the use and function of the ON/OFF trigger switch,
on/off switch for laser, upper and lower blade guards,
head hold-down latch, bevel lock handle, and cover plate
screw.
• Review
and understand all safety instructions and
operating procedures in this Operator’s Manual.
(SAFETY & OPERATION)
• Review
the
MAINTENANC
E and
TROUBLESHOOTING
GUIDE
for your miter saw.
• To
avoid injury or possible death from electrical shock:
Make sure your fingers do not touch the plug’s metal
prongs when plugging or unplugging your miter saw.
(ELECTRICAL EQUIREMENTS AND SAFETY)
BEFORE EACH USE INSPECT YOUR SAW
.
•
Disconnect the miter saw
.
To avoid injury from accidental starting, unplug the saw
before any adjustments, including set-up and blade
changes.
•
Compare the direction of rotation arrow
on the guard to
the direction arrow on the blade. The blade teeth should
always point downward at the front of the saw.
•
Tighten the arbor bolt
.
•
Tighten the cover plate screw
.
•
Check for damaged parts
.
Check for:
SAFETY INSTRUCTIONS FOR BASIC SAW OPERATION
BEFORE USING THE MITER SAW
Fig. AA
3
2
1
4
OPERATION
WARNING
To avoid mistakes that could cause
serious, permanent injury, do not plug the tool
in until the following steps are completed
:
• Alignment
of moving parts
• Damaged
electric cords
• Binding
of moving parts
• Mounting
holes
• Function
of arm return spring and lower guard: Push the
cutting arm all the way down, then let it rise until it stops.
The lower guard should fully close. Follow instructions in
TROUBLESHOOTING GUIDE
for adjustment
if necessary.
• Other
conditions that may affect the way the miter
saw works.
• Keep
all guards in place, in working order and proper
adjustment. If any part of this miter saw is missing, bent,
damaged or broken in any way, or any electrical parts
don’t work, turn the saw off and unplug it.
• Replace
bent, damaged, missing or defective parts before
using the saw again.
• Maintain
tools with care. Keep the miter saw clean for
best and safest performance. Follow instructions for
lubricating. Do not put lubricants on the blade while
it is spinning.
• Remove
adjusting wrench from the tool before
turning it on.
• To
avoid injury from jams, slips, or thrown pieces,
use only recommended accessories.
• Check
the dust bag before you work. Empty the bag
if it is more than half-full.
RECOMMENDED ACCESSORIES
• Consul
t the ACCESSORIES and ATTACHMENTS section
of this Operator’s Manual for recommended accessories.
Follow the instructions that come with the accessory.
The use of improper accessories may cause risk of
injury to persons.
• Choose
the correct 10 in. diameter blade for the material
and the type of cutting you plan to do.
Содержание KN M-2509RC
Страница 1: ...KN M 2509RC Slide compound miter saw10 Sierra angular compuesta deslizable 254 mm...
Страница 31: ...30 DIAGRAM PARTS Slide compound miter saw10 Sierra angular compuesta deslizable 254 mm KN M 2509RC...
Страница 62: ...DIAGRAMA DE PARTES 61 Slide compound miter saw10 Sierra angular compuesta deslizable 254 mm KN M 2509RC...
Страница 64: ...www knova com mx...
