Knick A405B Скачать руководство пользователя

Страница: 47 / 108

The alarm delay time delays the color change of the display backlighting to red, the
22 mA signal (if configured), and the alarm contact switching.

Error messages can be signaled by a 22 mA output current. In addition, a relay
contact (RELAY1 / RELAY2) can be configured as alarm contact.

Menu item

Action

Choices

Alarm delay

Enter value using





keys.
Press enter to confirm.

0...600 SEC
(10 SEC)

Sensocheck

Select Sensocheck (continuous
monitoring of sensor membrane
and lines).
Select ON or OFF using



keys.
Press enter to confirm.
(At the same time, Sensoface is
activated. With OFF, Sensoface is
also switched off.)

ON/OFF

Tempcheck

To monitor the temperature
probe with TC OFF selected:
Select Tempcheck ON using



keys.
Press enter to confirm.
Now, the temperature probe will
be monitored.

ON/OFF

Configuring the Alarm

Содержание A405B













































































































Результаты поиска

Содержание A405B

Отзывы:

Похожие инструкции для A405B

Бренды по названию

Популярные бренды

Knick A405B, Руководство пользователя

Результаты поиска

Содержание A405B

Отзывы:

Похожие инструкции для A405B

Бренды по названию

Популярные бренды