manualshive.com logo in svg

Knauer BlueShadow Series, Руководство пользователя

Поделиться
Скачать
Knauer BlueShadow Series Скачать руководство пользователя страница 46

47

Maintenance and care

Insert new needle seal.

Increasing the pressure stability of 
valves

By changing the disk springs inside the valve, the column 
switchings can be built up with greater pressure stability.

Steps

Figure

1. Removing the old 

needle seal

2. Insert the new nee-

dle seal (B) into the 
screw fitting (A).

3. Place the biconical 

seal (C) on the new 
needle seal and turn 
everything into the 
syringe connection 
at the valve.

4. Screw the screw fit-

ting (A) on the valve 
moderately tight.

5. Insert the injection 

syringe all the way 
into the new needle 
seal (C). Loosen the 
screw fitting until 
the injection syringe 
can still be pulled 
easily but with 
noticeable friction, 
straight out.

Fig. 45

Biconical seal, needle seal, 
and screw fitting of the 
syringe connection

Fig. 46

Schematic display of the 
syringe connection

C

B

A

Needle seal

 

 

DYNASEAL
bushing

 

 
 
 

 

 

Biconical
sealing ring

 

Valve

Order number

Maximum pressure

13P/1C

A1378

25 bar

17P/1C

A1379

50 bar

17P/1C with 1/16”

A1379-1

100 bar

Содержание BlueShadow Series




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды