Knauer BlueShadow Series Скачать руководство пользователя страница 2

Страница: 2 / 59

Table of contents

Table of contents

Note: For your own safety, be sure to

read

the manual and

always

observe the warnings and safety information on the

device and in the manual!

Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Overview valves and valve drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Multiposition valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Injection valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Connections of the ports at the positions

loading

and

injecting . . . . . . . . . . .

Series and operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Laboratory use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Where is it prohibited to use the device or system? . . . . . . . . . . . . . . . . . . . . .

Application examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Selection of a column . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Column selection with a 2-channel valve . . . . . . . . . . . . . . . . . . . . . . . . . .

Backflushing of a column . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Backflushing of a precolumn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Accumulation of a sample . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Precleaning of a sample by a precolumn . . . . . . . . . . . . . . . . . . . . . . . . . . .

Precleaning of a sample . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Alternating precleaning of a sample . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Symbols and labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Laboratory regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Solvents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PEEK connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Protective measures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Power supply and mains connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Target group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

To what should the user pay particular attention? . . . . . . . . . . . . . . . . . . . .

What expertise should users have to safely operate a HPLC device



or system? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Protective film on the screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Scope of supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Checking the scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Space requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Front view of the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Device display and buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Rear view of the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Manual valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Electrical valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

V7695A

Содержание BlueShadow Series




























































Результаты поиска

Содержание BlueShadow Series

Отзывы:

Бренды по названию

Популярные бренды

Knauer BlueShadow Series, Руководство пользователя

Результаты поиска

Содержание BlueShadow Series

Отзывы:

Бренды по названию

Популярные бренды