background image

BAC-120063CW-ZEC FlexStat 

     7 

Installation and Configuration Guide, Rev. G

Illustration 7—MS/TP Network End-Of-Line Termination

Illustration 8—EOL/Pull-Up Switch Positions

10K 

0-12 V

Input Pull-Up Switches

ON

OFF

Switch 

Pushed 

Right 

IN2

IN3

IN4

IN7

IN8

IN9

NOTE:  10K 

 inputs

  are configurable for
  Type II or Type III
  thermistors in
  FlexStat’s menu.

NOTE:  EOL = End
  Of Line of BACnet
  MS/TP network.

EOL Switches

Switch 

Pushed 

Left 

Network EOL (End-Of-Line) Termination

The controllers/thermostats on the physical ends of 

an EIA-485 wiring segment must have end-of-line 

termination installed for proper network operation. 

(See Illustrations 7 and 8.) If a FlexStat is at the physi-

cal 

end

 of the MS/TP network line, set 

both

 the EOL 

termination switches to 

On

 (to the 

right

) on the back 

of the circuit board. If not on the end, ensure that 

both switches are Off (to the left).

 WED 7/30 

 

       5:33 PM

 

 

      

COOL:

 

 

      OCC:

 

 

      FAN:

                                   

COOL CALLS 5

Configuration and Operation

Illustration 9—FlexStat Display and Button Functions

Right 

(Menu)

Left

(Override)

Down

Up

NOTE:  For additional information, see the relevant 

parts of the Configuration section in the 

FlexStat Operation Guide

 (but not all 

things apply to this model).

NOTE:

  Settings and adjustments may require a 

password.

DAT

Zone Information (# of 

Zones, # of Zones Calling 

for Cooling, and # of Zones 

Calling for Heating)

Configure the Application and Address

To access the menus, press the right button. 

Navigate 

the menus and change settings by pressing a combi

-

nation of buttons.

 Press the:

• 

Enter

 button to select and/or exit value editing.

• 

Up/Down

 button to move among 

entries

 (up/

down lines).

• 

Left/Right

 button to move among 

value fields 

(left/right spaces).

• 

Left

 button to return to the Home screen.

Configure the 

application

 through the menu system. 

From the Main Menu, select 

ADVANCED

 (enter 

password if needed) and then 

APPLICATION

 APPLICATION
DEGREES SCALE: °F

APP:

OPT: 2H/2C
ADDITIONAL SETUP
ZONE DEV INS RANGE

ROOF TOP

 

ADDITIONAL SETUP

DAMPER

FAN
SENSORS
ZONE HYSTERESIS: 2
VALVE HT OR CL: HEAT
DEVICE TYPE: 0-10V
STAGING

Содержание FlexStat BAC-120063CW-ZEC













Отзывы: