KMC Controls FlexStat BAC-12 Series Скачать руководство пользователя страница 26

Страница: 26 / 43

FlexStat

Operation Guide, Rev. L

MS/TP Network Communication

Connect the EIA-485 MS/TP network wiring and set

the EOL switches accordingly. (See the Installation

Guide for wiring and end-of-line switch informa-

tion.)
From the FlexStat menus, adjust the device instance

number, the MAC address, and baud rate from the

defaults as necessary. Set the Max Master to the

minimum necessary for the network. See

(Advanced)

BACnet Device Properties on page 16

and

(Advanced)

Communications (BACnet) on page 14

NOTE: The current FlexStat MAC address and

device instance numbers can be viewed in

the About menu. Each BACnet device on a

network must have a unique MAC address

and device instance.

Network Connection

IP/Ethernet Network Communication

Plug in an Ethernet cable into the (optional) RJ-45

jack on the back.
For

and

IP Foreign Device

communications,

consult with the system administrator for the

appropriate settings for the IP Address, Subnet

Mask, Gateway, and UDP Port.

Ethernet

communications are essentially plug-and-

play, and the MAC address is not changeable.

Only one protocol can be enabled at any time.

See

(Advanced) Communications (BACnet) on page 14

KMD-5624

Cable

KMD-5576

NOTE: For IP/Ethernet-enabled models, a FlexStat

in one of the Ethernet or IP modes must

(temporarily) be set for MS/TP mode (and

restarted) to communicate through the

data port at the bottom of the cover. See

(Advanced) Communications (BACnet) on

page 14

and

Resetting the FlexStat on page 24

IN9
IN8

GND

IN7

–A
IN4
IN3

GND

IN2

Common/–/C

Phase/ /R

Analog 9

GND 7–9
Analog 8
Analog 7
Relay 6
SC 4–6
Relay 5
Relay 4
Relay 3
SC 1–3
Relay 2
Relay 1

Outputs

(Wir

ing Cutout in Bac

kplate)

MS/TP
Network

Inputs

24 VAC

(Wiring is
dependent on
application)

Inputs

IP/Ethernet

Network

(Optional)

NOTE: IN1 and IN5–6 are

reserved for internal sensors

NOTE: SC = Switched

(relay) Common

PC Data Port Connection

The FlexStat is equipped with a PC data port located

at the bottom of the thermostat housing. This port

provides a temporary EIA-485 (formerly RS-485)

connection to the digital network for network setup

or troubleshooting.
To connect a computer to the port, a means of

converting the EIA-485 signal to a USB or EIA-232

(formerly RS-232) signal will be needed. For USB,

use a KMC KMD-5576 USB Communicator. For

EIA-232, use a third-party interface. (See the instruc-

tions included with those devices and software.) To

connect to the PC data port:
1. Connect the keyed, flat end of the KMD-5624

interface cable (included with the KMD-5576) to

the port on the bottom of the FlexStat.

2. Connect the modular plug of the cable to the

interface device that converts the EIA-485 signal

from the FlexStat into a USB or EIA-232 signal.

3. Connect the suitable cable from the interface

device to the computer’s serial or USB port.

Install any required software and configure the

port as necessary.

NOTE: To avoid faulty communication with the

KMD-5576 USB Communicator, the Max

Master number may need to be reduced

to the minimum required for the network

and the driver and latency settings on

the computer may need to be checked or

updated. See

Troubleshooting on page 28

Содержание FlexStat BAC-12 Series












































Результаты поиска

Содержание FlexStat BAC-12 Series

Отзывы:

Бренды по названию

Популярные бренды

KMC Controls FlexStat BAC-12 Series, Руководство по эксплуатации

Результаты поиска

Содержание FlexStat BAC-12 Series

Отзывы:

Бренды по названию

Популярные бренды