KMC Controls 68 Series Скачать руководство пользователя | Manualshive

Страница: 57 / 80

background image

55

OPERATIONAL SETUP

TRACTOR PREPARATION:

Before operating implement refer to tractor operator’s manual for information concerning safe methods
of operation, hydraulics, hitch adjustment, tire inflation, wheel adjustments and tractor weights.

Check tractor brakes and warning lights, make sure they are in proper working order.

Check tractor hydraulics oil reservoir and add oil if needed.

IMPORTANT:

It is recommended that the tractor’s Draft Control Feature be disengaged for optimal

performance of this tool.

WARNING

TRANSPORTING THE IMPLEMENT WILL ADD SIGNIFICANT WEIGHT TO
YOUR TRACTOR. MAKE SURE THE TRACTOR IS PROPERLY BALLASTED.

Front-End Weights:

Use front-end weights as needed to provide effective steering control and front-end stability.

See your tractors Operator’s Manual for recommendations on ballasting procedures.

WARNING

DO NOT EXCEED THE TRACTOR’S LIFT CAPACITY OR BALLAST
RECOMMENDATIONS.

NOTE

: Warranty consideration will only be given on items manufactured by Kelley Manufacturing Co.

Horse Power Requirements:

The power requirement for this unit is 25 - 40 HP per shank, depending on the depth of penetration and
ground conditions. Select a tractor with sufficient power to operate this machine.

Sway Blocks

Sway blocks should be used and adjusted to limit movement in operating position. Your implement
should be permitted to sway very little while operating and should be held rigid while transporting.

See your Tractor Operator’s Manual.

Wheel Spacing

Set tractor wheels so they are equally spaced from center of tractor. If using the tool to penetrate in
fields of row crops, set tractor wheels so they are centered between the rows.
See your Tractor Operator’s Manual for correct tire inflation pressure.

Drawbar Position

Place the drawbar in the short, center position to provide maximum clearance between drawbar and
tool.

«
...
55
56
57
58
59
...
»

Содержание 68 Series

















































































Отзывы:

Нет отзывов

Похожие инструкции для 68 Series

Бренд: Taylor Made Страницы: 2

Бренд: York Fitness Страницы: 18

Бренд: Safco Страницы: 2

Бренд: Omni Страницы: 193

Бренд: JB-Lighting Страницы: 60

Бренд: IBEX Страницы: 4

Бренд: Pari Страницы: 11

Бренд: Pari Страницы: 2

Бренд: Haas Страницы: 5

MCX-C15 - MusicCAST Network Audio Player

Бренд: Yamaha Страницы: 114

Бренд: RAMVAC Страницы: 53

Бренд: Toro Страницы: 4

Бренд: CA.MI Страницы: 40

Бренд: Launch Страницы: 15

Бренд: RayLight Страницы: 31

Бренд: PLUSLITE Страницы: 13

Бренд: Sandusky Lee Страницы: 8

GLUTE COASTER ABS1020

Бренд: ABS Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды