KMC Controls 68 Series Скачать руководство пользователя | Manualshive

Страница: 64 / 80

background image

62

1"- 2"

"C"

"D"

LEVELING IMPLEMENT TOOL BAR

Leveling Side To Side

Leveling Front To Rear

For best results, when leveling the implement, position the tractor with implement on a level floor.
Check tractor tire pressure and inflate equally from side to side. See your tractor operator’s manual for
correct tire inflation pressure.

   With the implement attached to tractor, raise the unit 1 to 2 inches off the floor.  Shut-off engine and
lock  brakes  on    tractor.    Measure  to  the  bottom  edge  of  the  rear  toolbar  tube  on  each  side  of  the
machine. Toolbar will be level when dimension “A” is the same as dimension “B” as shown in drawing
above.  Level toolbar from side to side by adjusting the lift links on tractor 3-point hitch.
  Before adjusting 3-point links see  your tractor operator’s manual for correct  adjustment procedures
and safety requirements.

Ground Line

"B"

"A"

1" - 2"

  Before  setting  the  Gauge  wheels  it  is  necessary  to  level  the  toolbar  from  the  front  to  the  rear.  For
initial adjustment keep the machine raised off the ground 1 to 2 inches (being sure bottom of shanks
clear floor). Measure from the floor to the bottom of the front toolbar tube and the rear toolbar tube. If
toolbar is not level from front to rear with ground line, extend or retract the tractor top link until toolbar
is  parallel  (  or  level)  to  the  ground  line.    Toolbar  will  be  level  when  dimension  “C”  is  the  same  as
dimension “D”.  Further front to back adjustment will be required once machine is operated in the field.
When properly leveled, all tillage components will enter the ground uniformly.

Rear Toolbar

Front
Toolbar

* NOTE: ALL HEIGHT DIMENSIONS GIVEN

IN THIS SECTION ASSUME TOOLBAR IS

RUNNING LEVEL TO THE GROUND.

«
...
62
63
64
65
66
...
»

Содержание 68 Series

















































































Отзывы:

Нет отзывов

Похожие инструкции для 68 Series

Бренд: GE Страницы: 14

Бренд: GE Страницы: 11

Бренд: GE Страницы: 20

Druck ADTS 2 Series

Бренд: GE Страницы: 18

Бренд: Fenton Страницы: 16

Бренд: Rational Страницы: 60

Бренд: TANACOM Страницы: 27

Бренд: iBACheck Страницы: 2

Бренд: Balanced Body Страницы: 4

Бренд: Balanced Body Страницы: 2

Reformer Trapeze Combination

Бренд: Balanced Body Страницы: 164

Бренд: Wacker Neuson Страницы: 50

Бренд: Balanced Body Страницы: 37

Бренд: EarthMark Страницы: 2

Бренд: Gabocom Страницы: 4

Бренд: W&S Страницы: 104

Бренд: CooperSurgical Страницы: 32

Design LED Panel 72IP MKII

Бренд: Elation Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды