KMC Controls 68 Series Скачать руководство пользователя | Manualshive

Страница: 12 / 80

background image

10

5.

Do not allow children to operate the Ripper Bedder. Only experienced

tractor operators should operate the tractor when using the Ripper
Bedder.

6. Stay clear of hydraulic lines, as they maybe under extreme pressure or heat.

7. Drive safely during transport; excessive speed while turning or on rough

ground could cause damage to the Ripper Bedder and/or cause the tractor to
tip over.

(Maximum speed of implement should never exceed 20 mph on

highway and 10 mph off-highway.)

8. Make sure hitch components are attached securely before operating or

transporting.

9. Use flashing warning lights when on highways, except where prohibited by

law.

10. Disengage PTO, apply parking brake, and stop tractor engine before

dismounting  tractor.  Allow  mechanisms  to  stop  completely  before  cleaning,
working,  or  adjusting  on  machine.    Even  when  the  tractor  is  stationary,  you
should  make  sure  it  is  properly  secured  and  made  safe  by  following  the

Safe Stop procedure

:

1.  Handbrake/Footbrake on
2.  Controls in neutral/park
3.  Engine off
4.  Key out

11.

Keep hands, feet and clothing away from moving parts.

12.

Make sure everyone is clear of machine before starting

tractor or operating

machine.

13.

Observe all safety decals located on machine.

Replace them if they become

damaged.

HIGH VOLTAGE SAFETY ACT

Georgia Law requires that anyone operating equipment within 10 feet of an overhead

high voltage line of more than 750 volts, must contact the Utilities Protection Center
(UPC) by telephone at least 72 hours before commencing the work. For more
information call (811), toll free (1-800-282-7411) or visit on the web
“www.gaupc.com”.

Please

contact your local power company about laws before

operating near high voltage lines.

«
...
10
11
12
13
14
...
»

Содержание 68 Series

















































































Отзывы:

Нет отзывов

Похожие инструкции для 68 Series

Бренд: Raymarine Страницы: 55

Бренд: Halyard Страницы: 4

Underwater Light Show & Fountain

Бренд: GAME Страницы: 2

Бренд: Makita Страницы: 60

Бренд: JB-Lighting Страницы: 60

Бренд: JB Systems Страницы: 7

Бренд: 3B SCIENTIFIC PHYSICS Страницы: 36

Бренд: 3A HEALTH CARE Страницы: 16

Short/cut 2000 Audio Editor

Бренд: 360 Systems Страницы: 4

Бренд: idiag Страницы: 12

Бренд: Abus Страницы: 12

Бренд: RAMVAC Страницы: 53

Бренд: GE Страницы: 194

Бренд: Harris Страницы: 21

Бренд: Petromax Страницы: 16

Бренд: SereneLife Страницы: 4

Monolith NT.115

Бренд: Nano Temper Страницы: 24

SCAFFOLDBENCH I-CISRL

Бренд: MetalTech Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды