KMC Controls 56 Series Скачать руководство пользователя страница 11

Страница: 11 / 46

SAFETY PROCEDURES (CONTINUED)

6. Drive safely during transport; excessive speed while turning or on rough ground could

cause damage to the Stalk Shredder Puller and/or cause the tractor to tip.

(Maximum

speed of implement should never exceed 20 MPH on higher capacity highways and

should never exceed 10 MPH on lower capacity roads.)

7. Make sure hitch components are attached securely before operating or transporting.

8. Use flashing warning lights when on highways, except where prohibited by law.

9. Apply parking brake and stop tractor engine before dismounting tractor. Allow

mechanisms to stop completely before cleaning, working, or adjusting on machine. Even

when the tractor is stationary, you should make sure it is properly secured and made safe

by following the

Safe Stop Procedure:

1. Handbrake/Footbrake on

2. Controls in Neutral/Park

3. Engine off

4. Key out

10. Keep hands, feet, and clothing away from moving parts.
11. Make sure everyone is clear of the machine before starting the tractor or operating

machine.
12. Observe all safety decals located on the machine. Replace them if they become damaged.

HIGH VOLTAGE SAFETY ACT

Georgia Law requires that anyone operating equipment within 10 feet of an overhead high

voltage line of more than 750 volts, must contact the

Utilities Protection Center (UPC)

telephone at least

72 hours

before commencing the work.

For more information, call (

811

), or Toll-Free (

1-800-282-7411

), or please visit

http://

gadistrictupc.com.
Please

contact your local power company in reference to their laws and regulations before

operating near high voltage lines.

Содержание 56 Series















































Результаты поиска

Содержание 56 Series

Отзывы:

Похожие инструкции для 56 Series

Бренды по названию

Популярные бренды

KMC Controls 56 Series, Руководство пользователя и каталог запасных частей

Результаты поиска

Содержание 56 Series

Отзывы:

Похожие инструкции для 56 Series

Бренды по названию

Популярные бренды