Klutch 49416 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 27

Klutch 49416 Скачать руководство пользователя страница 15

Page 15 of 27

Refer to Figure L and Figure M

18. Mount the inner Motor Base Cover and Motor Mount Plate.

a. To prepare the Motor (42) for mounting, remove the Motor from the Inner Motor Base Cover

(39) by unthreading the two Hex nuts and Hex bolts holding it in place for shipping.

b. Mount the Inner Motor Base Cover (39) to the Shaft (35), slide Flat Washersonto two Bolts

(24), and insert the Bolts through the Motor Base Cover and the Iron Tube Fixture (15).
Secure withWashersand Lock Nuts.

c. Attach the Motor Mount Plate (40) to the Inner Motor Base Cover (39), insert four Bolts (37)

through the holes in the Fixed plate (38), Cushion (62), Motor Base Cover channels. Thread
Locknuts (55) and washeronto the Bolts, but DO NOT tighten the locknut at this stage.

Note: The Motor Mount Plate must be adjusted up ordown to tighten the V Belt (61).

Bolt &Washer

Washer &Locknut

Motor Mount Plate (40)

Inner Motor
Base Cover (39)

Channels

Bolt &Washer
Washer &Locknut

Cushion

Locknut (55)

Fixed plate (38)

Bolt &

Channels

Fig.L

Fig.M

«
...
13
14
15
16
17
...
»

Содержание 49416




























Отзывы:

Нет отзывов