Klutch 49416 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 27

Klutch 49416 Скачать руководство пользователя страница 11

Page 11 of 27

Assembly Instructions

Refer to Figure A

1. Place Stand (30) onto Hinge Bracket (34) so that the bolt holes line up.

2. Insert Hex Bolts (26) with Washer (27) through the holes from one side, then Washer (27) and

Lock Nut (23) from the other side, and tighten with a wrench.

3. Insert Support Bracket (25) onto Stand (30) so that the bolt holes line up.

4. Insert Hex Bolts (26) with Washer (27) through holes from one side, then Washer (27)and Lock

Nut (23) from the other side, and tighten with a wrench.

Refer to Figure B

5. Place

Stand

upright.

6. Place Wheel (33) onto Hinge Bracket (34) axle, and slip on theWasher (32) after the wheel.

7. InsertPins (31) into the Hinge Bracket (34) axle holes, outsideeach Flat Washer. The pin should

be touching the washer, not the wheel.

8. Bend each side of the Pins outward so they do not fall out.

Pin (31)

Wheel (33)

Fig.B

Fig.A

Stand (30)

Bolt M8X70 (26)

Support bracket (25)

Washer

Φ

8 (27)

Hinge bracket (34)

Lock Nut M8 (28)

«
...
9
10
11
12
13
...
»

Содержание 49416




























Отзывы:

Нет отзывов