Klutch 49416 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 27

Klutch 49416 Скачать руководство пользователя страница 12

Page 12 of 27

Refer to Figure C

9. With two people, set the Drum Lower (8) with attached Support Arm assembly into Stand

assemblyso that the Shaft (35) is on the wheel side and the Iron Tube (18) is on the Support
Bracket (25) side of the assembly.

10. Insert Hex Bolts (59) with Washer through holes from one side, thenWasher and Lock Nutfrom

the other side, and tighten with a wrench.

Refer to Figure D

11. With the help of another person, attach Connector Seal (6)to the DrumLower (8), making sure that

the holes in both align. This Connect Seal must be flat on the Drum Lower to ensure a proper seal.

Refer to Figure E

12. Carefully place the Drum Upper (4) onto the Connector Seal. Make sure that the holes in both

align. Note: When placing the Drum Upper, align the Mixing Blade mounting holes in the side of
the drums as shown in FigureE. If they are too far away from each other, the Mixing Blades holes
will not match up with the mounting holes on the Drums.

Refer to Figure F

Mixer Blade

Mount holes

Drum Upper (4)

Fig.E

Fig.D

Connect Seal (6)

Fig.C

Iron Tube

(18)

Shaft (35)

Bolt &Washer

&Locknut

Bolt &Washer

&Locknut

«
...
10
11
12
13
14
...
»

Содержание 49416




























Отзывы:

Нет отзывов