klover DIVA SLIM Скачать руководство пользователя страница 31

Страница: 31 / 52

DIVA SLIM AIR PELLET STOVE

EN - Rev. 1.0

- MAC ADDRESS and REGISTRATION CODE, which appear on the label affixed near the “Support panel”

(see

“Components of the appliance”)

12.

At this point, the appliance will be added and can be managed through the Web app from any device (PC / tablet /

smartphone) connected to the Internet.

It can be accessed from the address

http://appwifi.klover.it/it/

or via the “My KLOVER” app, which can be

downloaded from various stores (Apple, Android, etc).

START-UP

Initial start-up

Perform the following operations:

Connect the appliance to the electrical system by using the provided cable;

Set the “power ON/OFF switch” on the rear side of the appliance to “

” (on);

Fill the pellet tank; for the initial start-up, to avoid wasting the time required to fill the entire auger channel (this

should be done whenever the appliance runs out of pellets), we recommend following the instructions of “MENU

06 – INITIAL LOAD”;

Switch the appliance on by pressing the “ON/OFF” button located on remote control (button 3) or on the support

panel (button 1). See the instructions below. Warning: before switching on the appliance, make sure the brazier

is clean and that there are no pellets inside it; otherwise, empty and/or clean it.

We recommend that you use high quality pellets so as not to impair the operation of the appliance. Damage

caused by poor-quality pellets shall not be covered by the warranty.

Do not pour pellets manually into the brazier.

Ignition cycle

Prolonged pressing of button 3 (On/Off) on the remote control or of button 1 (On/Off) on the support panel allows for

switching the appliance on.
The ignition cycle can last 20/25 minutes max. and is divided into five steps:

Phase

Display message

Meaning

Duration

CHECK UP

Brazier cleaning cycle

Roughly 30

seconds

LOAD PELLET

Pre-loading of the brazier with pellets (continuous pellet loading) to fill the brazier
sufficiently to allow correct ignition

Roughly 4 minutes

FLAME STAND-BY

Stand-by for flame ignition after pre-loading (pellet loading suspended)

Roughly 4 minutes

FLAME STAND-BY /

LOAD PELLET

Loading of pellets into the brazier (intermittent pellet loading)

Not ascertainable

FLAME LIGHT

Flame stabilisation to allow uniform ignition of all pellets that were not burned in the
previous phases

Roughly 8 minutes

At the end of the ignition cycle, the appliance enters the work mode at the power set under “SET OUTPUT”.

MAC Address

Registration code

Содержание DIVA SLIM





















































Результаты поиска

Содержание DIVA SLIM

Отзывы:

Бренды по названию

Популярные бренды

klover DIVA SLIM, Установка, использование, техническое обслуживание и полезные советы

Результаты поиска

Содержание DIVA SLIM

Отзывы:

Бренды по названию

Популярные бренды