klover DIVA SLIM Скачать руководство пользователя страница 29

Страница: 29 / 52

DIVA SLIM AIR PELLET STOVE

EN - Rev. 1.0

A new page will open up (Welcome to WiFiMi Setup) containing all the data relative to the previous configuration. To

reconnect the module to the indicated network, go to “Menu 08 – WIFI STATUS” of the remote control, select

“RESET” and wait for value “08” (Module connected) to appear under “WIFI STATUS”. If you wish to connect to a
new network, press the “Search Wi-Fi Networks” button.

The last configuration page will then open up (Search available Wi-Fi networks). Select the network to be used from

the list in order to connect the appliance to the Internet then enter the password for the selected network. If the

network is hidden, click on “Custom SSID” and enter the two parameters requested.

Click on “Connect” to connect the appliance to the selected Wi-Fi network.

Содержание DIVA SLIM





















































Результаты поиска

Содержание DIVA SLIM

Отзывы:

Бренды по названию

Популярные бренды

klover DIVA SLIM, Установка, использование, техническое обслуживание и полезные советы

Результаты поиска

Содержание DIVA SLIM

Отзывы:

Бренды по названию

Популярные бренды