klover DEA PLUS, Руководство пользователя

Страница: 58 / 82

16
WHAT HAPPENS IF..
…the pellet does not ignite
With no ignition. The
“NO IGNIT“
alarm message appears.
Cancel the alarm and bring the stove to standard condition by pressing key 4 for a few seconds.
...the fire door is open or closed improperly
In case the door is open or closed improperly, the motor reducer cannot be powered electrically, not allowing the stove to switch on. If the fire door is
opened during the normal functioning, the stove burns all the pellet in the brazier, activating the
“NO PELLET”
alarm (sudden switch off).
...the flue is dirty, blocked or not manufactured correctly
In case the flue is dirty, blocked or not manufactured correctly, the motor reducer cannot be powered electrically not allowing the stove to switch on. If the
flue blocks during the normal operation, the stove burns all the pellet in the brazier, activating the
“NO PELLET”
alarm (sudden switch off).
…the pellet tank goes in over-temperature
The motor reducer is not electrically powered with pellet tank over-temperature as the thermostat intervenes in manual re-arm. If it happens with stove
working, the latter goes in
“NO PELLET”
alarm (sudden switch-off). Therefore the thermostat must be rearmed before switching on the stove.
...lack of power (black out)
Upon restore after power outage due to time less than Pr48, the stove immediately re-starts from operative state it had before power outage (recovering the
set work power).Upon restore after power outage due to time more than Pr48, the stove sets on
“STOP FIRE” (stand-by)
mode and carries out the entire
switch off cycle until its cooling. Once this phase is completed, the thermo stove can be normally switched on to proceed working at the set power.
Previous state Black-out duration State after power restore
OFF Any OFF
START duration < Pr48 START
START duration > Pr48 START
LOAD PELLET Any BLACK OUT ALARM
WAITING FIRE Any BLACK OUT ALARM
FIRE ON duration < Pr48 FIRE ON
FIRE ON duration > Pr48 STOP FIRE with automatic re-ignition after machine cooling
WORK (any phase) duration < Pr48 WORK (any phase)
WORK (any phase) duration > Pr48 STOP FIRE with automatic re-ignition after machine cooling
BRAZIER CLEANING duration < Pr48 BRAZIER CLEANING
BRAZIER CLEANING duration > Pr48 STOP FIRE with automatic re-ignition after machine cooling
FINAL CLEANING duration < Pr48 FINAL CLEANING and after cooling

OFF
FINAL CLEANING duration > Pr48 FINAL CLEANING and after cooling

OFF
STOP FIRE Any STOP FIRE
CIRCUIT BOARD PARAMETERS
THE PARAMETERS MEMORISED ON THE CIRCUIT BOARD ARE FUNDAMENTAL FOR THE CORRECT FUNCTIONING OF THE STOVE.
THE PARAMETERS GIVEN BELOW ARE ALREADY MEMORISED IN THE STOVE INSPECTION PHASE DIRECTLY IN THE FACTORY.
THESE PARAMETERS ARE THE RESULT OF CAREFUL TESTS WITH VARIOUS TYPES OF PELLETS AND MUST NOT BE CHANGED WITHOUT
THE AUTHORISATION OF KLOVER srl, SO AS NOT TO JEOPARDISE STOVE FUNCTIONING.
ALL RESPONSIBILITIES ARE DECLINED FOR DAMAGE CAUSED BY INCORRECT INTRODUCTION OF THE PARAMETERS.
“Various calibrations” (Menu M – 9 – 5)
Parameter Menu level Description Display writing Measurement Value field Database
Pr38 M
– 9 – 5 – 01
Re-ignition block RE-IGNIT BLOCK Minutes 0
– 10
5
Pr39 M
– 9 – 5 – 02
Flue gas intake device switch-off time MIN-INT OFF Minutes 0
– 20
10
Pr40 M
– 9 – 5 – 03
Pre-load time in ignition IGNIT PRE-LOAD Seconds 0
– 225
95
Pr41 M
– 9 – 5 – 04
Stand-by time after pre-load AFTERPRE STANDBY Seconds 0
– 255
170
Pr42 M
– 9 – 5 – 05
Intake device speed in pre-load phase EXHMOTOR PRELOAD Revs/min 500
– 2800
2200
Pr43 M
– 9 – 5 – 06
ON/OFF temperature hysteresis
“SET ROOM”
DELTA ON OFF AUTO °C 0
– 15
2
Pr44 M
– 9 – 5 – 07
Delay to economy switch-off (timer after
reaching
“SET ROOM” + Pr43
)
DELAY OFF AUTO Minutes 2
– 120
2
Pr45 M
– 9 – 5 – 08
Power change delay POWER CHANGE Seconds 0
– 60
30
Pr46 M
– 9 – 5 – 09
Exchanger 1 motor speed in switch-off phase AIR IN OFF Volt 65
– 225
225
Pr47 M
– 9 – 5 – 10
Keypad block enabling KEYS BLOCK EN On
– off
On
– off
OFF
Pr48 M
– 9 – 5 – 11
Automatic re-ignition after black-out BLACK OUT IGNITION Seconds 0
– 60
30
Pr49 M
– 9 – 5 – 12
Room probe calibration ROOM-T OFF-SET °C - 9
– 9
0