background image

3

.7.2 Form the piping

A. Form the piping by wrapping the connecting portion

of the indoor unit with insulation material and secure
it with two kinds of vinyl tapes.
• If you want to connect an additional drain hose, the end

of the drain outlet should be routed above the ground.
Secure the drain hose appropriately.

B  In cases where the outdoor unit is installed below the

indoor unit perform the following.
1) Tape the piping, drain hose and connecting cable from

down to up.

2) Secure the tapped piping along the exterior wall using

saddle or equivalent.

,

Taping

Pipings

Connecting
cable

Drain
hose

Seal small openings
around pipings with a
gum type sealer.

Trap is required to prevent water
from entering into electrical parts.

C. In cases where the Outdoor unit is installed above

the Indoor unit perform the following.
1) Tape the piping and connecting cable from down to

up.

2) Secure the taped piping along the exterior wall. Form

a trap, to prevent water entering the room.

3) Fix the piping onto the wall by saddle or equivalent.

Trap

Seal small openings
around pipings with a
gum type sealer.

,

Trap

Trap is required to prevent water
from entering into electrical parts.

3

.7 Checking the Drainage and forming

the pipings

3

.7.1 Checking the drainage

A. To remove the front panel from the indoor unit,

remove the front panel from the indoor unit cabinet.
1) Set the air direction louvers up-and-down to the posi-

tion(horizontally) by hand.

2) Remove 3 screws that retain the front panel.

Pull the lower left and right sides of the grille toward
you and lift it off.

Grille

Remove screws (3places)

Chassis

B. To check the drainage.

1) Pour a glass of water on the evaporator.
2) Ensure the water flows through the drain hose of the

indoor unit without any leakage and goes out the drain
exit.

,,

,,

C. Drain piping

• The drain hose should point downward for easy drain

flow.

• Do not make drain piping.

Downward slope

Do not raise

Accumulated
drain water

Tip of drain hose 
dipped in water

Air

Waving

Water
leakage

Water
leakage

Ditch

Less than 
50mm gap

Water
leakage

Air Conditioner Service Manual

13

Содержание KSWT SERIES


















Отзывы: