background image

3

.6.2 Connect the cable to the outdoor unit

A. Remove the control cover from the unit by loosen-

ing the screw.
Connect the wires to the terminals on the control
board individually.

B. Secure the cable onto the control board with the

cord clamp.

C. Refix the control cover to the original position with

the screw.

D. Use a recognized circuit breaker 20A(18K) ,

25A(24K) between the power source and
the unit. A disconnecting device to adequately dis-
connect all supply lines must be fitted.

Terminal block

Over 5mm

Control cover 

Power cord
(power connecting
cable)

Connecting cable

Outdoor unit

After the confirmation of the above conditions, prepare the wiring as follows:

1) Never fail to have an individual power circuit specifically for the air conditioner. As for the method

of wiring, be guided by the circuit diagram posted on the inside of control cover.

2) The screw which fasten the wiring in the casing of electrical fittings are liable to come loose

from vibrations to which the unit is subjected during the course of transportation. Check them
and make sure that they are all tightly fastened. 
(If they are loose, it could cause burn-out of the wires.)

3) Specification of power source.

4) Confirm that electrical capacity is sufficient.

5) See to that the starting voltage is maintained at more than 90 percent of the rated voltage

marked on the name plate.

6) Confirm that the cable thickness is as specified in the power source specification.

(Particularly note the relation between cable length and thickness.

7) Always install an earth leakage circuit breaker in a wet or moist area.

8) The following would be caused by voltage drop.

• Vibration of a magnetic switch, which will damage the contact point, fuse breaking, disturbance of the normal

function of the overload.

9) The means for disconnection from a power supply shall be incorporated in the fixed wiring and

have an air gap contact separation of at least 3mm in each active(phase) conductors.

CAUTION

Air Conditioner Service Manual

12

Содержание KSWT SERIES


















Отзывы: