background image

3

Instruction manual

EK 135L

HE.13451_A © 01/2013 R&D-2

IMPORTANT SAFETY INFORMATION

SAFETY
ALERT
SYMBOL

This symbol is used to call your attention to hazards 
or unsafe practices which could result in an injury or 
property damage. The signal word, defi ned below, 
indicates the severity of the hazard. The message 
after the signal word provides information for pre-
venting or avoiding the hazard.

Immediate hazards which, if not avoided, WILL result 
in severe injury or death.

Hazards which, if not avoided, COULD result in 
severe injury or death.

Hazards or unsafe practices which, if not avoided, 
MAY result in injury or property damage.

Read and understand all of the 
instructions and safety information 
in this manual before operating or 
 servicing this tool.

Failure to observe this warning 
could result in severe injury or death.

Electric shock hazard:

This tool is not insulated. When 
using this unit on or near energized 
electrical lines, use proper personal 
protective equipment.

Failure to observe this warning 
could result in severe injury or death.

Wear eye protection when operating 
or servicing this tool. 

Failure to wear eye protection could 
result in serious eye injury from 
fl ying debris or hydraulic oil. 

Skin injection hazard:

Do not use hands to check for oil 
leaks. Oil under pressure easily 
punctures skin. If injured, seek 
medical attention immediately to 
remove oil.

Failure to observe this warning 
could result in serious injury, gan-
grene, or death.

Do not use solvents or fl ammable 
liquids to clean the tool body. 
Solvents or fl ammable liquids could 
ignite and cause serious injury or 
property damage.

An incomplete crimp can cause a fi re.

Use proper die, connector, and cable combina-

• 

tions. Improper combinations can result in an 
incomplete crimp.

The relief valve sounds and the ram automatically 

• 

retracts to indicate a completed crimp. If you do 
not hear the sound of the relieve valve or the ram 
does not automatically retract, the crimp is not 
complete.

Failure to observe these warnings could result in 
severe injury or death.

Содержание EK 135L















Отзывы: