background image

Instruction 

manual 

K502 

       page 

13 

__________________________________________________________________________ 
 

4.2. Description of the operation functions

 

 
In order to remove the hook (Pos.-No. 2) the pump lever (Pos.-No. 1) will be pressed 
towards the body of the pump so that the hook can be pushed aside and thus releasing the 
pump lever. 
 
By actuating the pump lever with the foot the cutting cycle will be initiated. After 
continuously actuating the pump lever the pump will switch off automatically when 
reaching the max. operating pressure at 700 bar. Reaching this point will be indicated by 
an audible „click“. The pump has a double piston which allows a fast approach of the 
blades to the cable in a low pressure mode. When the cut starts the pump will 
automatically switch over to the high pressure mode. 
 
Before terminating the cutting cycle the blades can be manually retracted by actuating the 
release lever (Pos.-No. 3) e.g. in case of a handling error. 
 
If a pressure pick up is available the pressure increase can be observed. 
 

5.   Remarks in respect to the determined use 

 
The pump must be positioned on an even surface with a max. angle of 15°. 
 
In combination with a 2 m high pressure hose it is not possible to work in a cable trench. 
For this application you need at least a 3m pressure hose. 
 

5.1. Operation of the unit

 

 
1.)  Then roll out the hose completely and connect the crimping head (Pos.-No. 6) with 

the high pressure hose (Pos.-No. 5) via a coupling (Pos.-No. 8). This is done by 
pluging the male part of the coupling which is on the hose into the female part of the 
coupling mounted on the crimping head until they are securely engaged. Finally the 
coupling sleeve is secured with a lock (Pos.-No. 9), a threaded sleeve, to block the 
retractable sleeve of the female coupling. 
 

Attention 
Don’t actuate the pump without the crimping head. 

 

Attention 
Before operating the unit the oil level must be checked and adjusted if 
necessary. 

 

2.) Bring the cutting head into a proper cutting position. 
 
3.) Actuate the pump lever (Pos.-No. 1) continuously until the blades are completely 

closed and the cable is fully cut. 

 

4.) After the cutting cycle has been completed, the release valve responds and the blades 

retract automatically. 

Содержание K502




















Отзывы: