background image

63813-2100 Modular Card Extractor Tool 

Doc No.  63813-2100 

Release Date: 05-10--06 

UNCONTROLLED COPY

 

Page 1 of 5 

Revision: A 

Revision Date: 05-10-06 

 
 

Module Card Extractor Tool 

Instruction Manual 

Part No. 63813-2100 

 
 

FEATURES 

 

This tool is designed for the removal of the memory module card from the metal latch 87814 series Molex sockets, 1mm pitch, 
276-circuit vertical press-fit with metal latch DDR2. 

 

SCOPE 

Products:  87814 Series 276 Circuit Vertical Press-fit Metal Latch DDR2 Dimm Connector System.  See Product List below for specific part 
numbers. 

Product List 

The following is a partial list of the product order numbers and their specifications this tool is designed to run.  Updates to this list are 
available on www.molex.com. 
 

Assembly Order Number 

Description 

87814-1001 
87814-1002 

1.00mm (.039") Pitch DDR-2 DIMM Socket, Vertical, 

Press-fit, 276 Circuits Metal Latch 

 
 

DESCRIPTION 

 
The 1mm pitch, 276-circuit vertical press-fit with metal latch DDR2 
takes up a much smaller space inside the housing than a conventional 
latch will.  The entire connector length is almost similar to the module 
card.  However, the latch cannot be extracted by hand and this 
extraction tool is required to withdrawal the module card from the 
metal latch. 
 
The Module Card Extractor Tool consists of modular card latch, metal 
latch, and thumb pusher with a handle. 
 
 
 
 
 
 

METAL LATCH PUSHER 

Figure 1 

THUMB PUSHER 

MODULE CARD 

LATCH 

HANDLE 

Содержание 63813-2100






Отзывы: