Klark Teknik HELIX DN9848E страница 44 Скачать руководство пользователя

Страница: 44 / 52

Remote Control Setup

9.4.2

Connection and Configuration Procedure

The remote control PC is connected to the system as follows:

To connect, set up and configure your system for serial operation

Connect the HELIX DN9848E units in a daisy chain configuration, see Section 9.2.1.

Power up the HELIX DN9848E units and assign each one a unique Comms channel
address, as described in Section 7.2.

Note

The order of the addresses does not need to mirror the order of the daisy chain

networking, but each unit MUST have a unique comms channel address.

Referring to the following table, connect your laptop/PC to the first HELIX unit in the

daisy chain.

HELIX DN9848E Unit

Connection

Laptop/PC

Connection

Cable/Converter Required

D9 COM port

Host cable

RS-232 input to front panel

“PC PORT”

USB port

KK systems USB/232 converter plus host cable

For details of converters plese refer to
http://www.klarkteknik.com/faq_connections.htm

For details on configuring and controlling the DN9848E from the Elgar Library Manager and HELIX

DN9848E RCS add-in software, please refer to the relevant documentation.

Содержание HELIX DN9848E





















































Результаты поиска

Содержание HELIX DN9848E

Отзывы:

Похожие инструкции для HELIX DN9848E

Бренды по названию

Популярные бренды

Klark Teknik HELIX DN9848E, Руководство оператора

Результаты поиска

Содержание HELIX DN9848E

Отзывы:

Похожие инструкции для HELIX DN9848E

Бренды по названию

Популярные бренды